I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello, I am porting to nRF5340 from nRF52833. Previously, we were using sdk17.0.2 for nRF52833 and we were able to successfully implement encryption algorithm AES-CTR-128...
Hi,
I have a NRF52840-DK (400236). I was using it for the development. It was working perfectly.
Suddenly the issue arises the power section is heating up.
I am powering...
Hi,
I am running the standard Grove LCD code, as below but am getting an error, " Grove LCD: Device not ready.'
the code is
my overlay file is
and my proj...
Hello,
we have a set of router devices already on the market: each of them was developed using 4.0 stack.
now we're aligning the stack to the 4.2 version observing a very...
Hi!
I've followed the app timer example to implement app timers in my project. My project is low power consumption oriented. When I use a repeated timer, power consumption...
Hello,
We are integrating the nordic sdk for DFU on our own application on Android and iOS.
We need to know al the possible error codes that the sdk can sent but we...
Hi DevZone,'
I am trying to use the crypto library with CC310 backend on a FreeRTOS application using the nRF52840DK.
My problem seems to be that when initializing the...
Hello,
I am trying to set the default TX power to +8dbm for all stages of the BLE transmission process, including when advertising is active. I have referenced the "hci_pwr_ctrl...
Hi,
My project is set up as out-of-tree using NCS v2.0.0. I would like to restrict the NCS version such that it will throw a compile-time error if a non-matching version...
I am using SDK v16.0.0 with s140 softdevice. In app_util.h, there is STATIC_ASSERT_SIMPLE and STATIC_ASSERT_MSG definition decided by platform like __CC_ARM or __GNUC__. ...
Dear Nordic fellows,
I have a NRF52832 and I want to configure the UARTE peripheral driver in not blocking mode. I want to try and exploit the double buffered DMA. I'm using...
I am using UART to try to send and receive data from the MCU on my nRF9160 board. I noticed in the tutorial on DevAcademy that using the asynchrounous mode, we're able to...
Hi！
Due to product requirements, I need to make the broadcast package contain 128-bit UUID so that the APP of our company can identify the device. The chips of other manufacturers...
Hi
I am using NRF5340 chip in my custom designed board and I want to use all the 4 UARTs available in this chip at the same time.
The interesting problem which I am confronting...
