I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hello,
I just received an nRF21540 EK, I am trying to use it on my current hardware which is only for scanning beacons (won't transmit) so need use it as LNA in the received...
Hi everyone. I have to turn off the bluetooth module to save battery. I am using the SDK example "ble_app_template_pca10056_s140". To start the advertisement I use the "ble_advertising_start...
project set up: Development board used nrf52832 ,SDK 15.0 ,SEGGER 5.10
actually i want to read data string from ESP32 using nrf52832 via UART (RX,TX) and send it to nrf...
Hello All,
We are using Power Profilier Kit 2 for measuring the current consumption of our device.
We Start the measurement at 14:16 PM. after 1 hour and 39 minutes (at...
HI,
we are working with
nRF5 SDK v15.2.0 ------------------------ Release Date: Week 37, 2018
Our use-case has a central device, which has 7 to 10 peripheral connected...
Hello,
We are using nRF Connect SDK 1.8.0 with nRF52832. As per the nRF Connect Documentation, when there is no active task, idle thread is called. Could you let us know...
Good morning,
I' mi trying to improve power saving on a device and it would be great to trigger:
1.an NRF52832 input pin transition triggers a "SPI1 instance" reading...
Hello,
I want to send 614.4 kHz clock signal to GPIO.
I checked that GPIOTE example could be used for this.
When I update uint32_t cc_value at nrf_drv_timer_extended_compare...
In searching, I haven't been able to find much information on implementing USB CDC ECM. Has anyone successfully implemented CDC-ECM with an nRF52? Alternatively, has anyone...
Dear nRF,
I know this topic has been covered many times, but I am unsure how I can change the uart pins for BLE 2-wire? I have not found any configuration for it inside...
Hi,
We've been in the process of debugging our development board but are having issues. When we try to connect to our board we get:
ERROR: [SeggerBackend] - JLinkARM...
I am using the Segger interface for designing an nRF52 based device. I am planning to use SWDIO SWCLK VTref and GND pins on my device. Is it necessary to connect the nRESET...
Hi!
We upgraded our node version 12.x to v 14.x and are trying to run in on Ubunto. "yarn install" trying to download pc-ble-js driver automaticly from the rebository git...
