Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Tried to compile the Bluetooth: Peripheral UART-sample, (nRF Connect SDK v1.9.1) and got an error:
FATAL ERROR: command exited with status 1: 'c:\ncs\v1.9.1\toolchain\opt...
Hi,
I am devloping base on azure_fota example and got the Peer closed connection! after used the SAS URL.
First, I complete do the FOTA by using the normal URL from blob...
I am working on my nrf52810 . I just found an issue that, when my device enter DFU mode its show dfu trag , I can not return to the application(If I do not want to upload...
Hi,
1. Is bootloader file and firmware file, different for projects build on nCS..? Or a single executable build file consists both bootloader & firmware..?
2. Can you...
Hi
I am working on driver for SPIS and would like to run higher than 8 MHz. We have been doing some tests and seems like it is possible to go e.g. 10 MHz.
Is the nrf51810_PS...
Hi,
How can I put an application at a specific memory location?
I want to upload 2 programs to my device and switch between these applications. I modified the bootloader...
Olfox recently raised a concern with the 400kHz frequency setting for the TWIM peripheral, which I confirm is incorrect in the SDK (17) and nRF52832 datasheet (v1.7); I attempted...
As described in that PR I am getting a hard fault when trying to cancel a download.
https://github.com/nrfconnect/sdk-nrf/pull/6955
To reproduce this issue apply the...
Hello! We are developing a board with NB-IoT connection base on the nRF9160 but also BLE capabilities based on the nRF52832. While researching the best way to implement this...
What is the default path of Kconfig in SES Project ? I testing Azure-Iot_Hub sample project. I define the AZURE_IOT_HUB_DEVICE_ID and AZURE_IOT_HUB_NAME in prj.conf file....
TLDR; How do I access GPIO and other peripherals via SEGGER IDE without using Zephyr when creating a new project as "New > New Project > Nordic A C/C++ Executable". Please...
Hi,
We are building an application on the nrf5340 application core. We noticed that library calls are being made to perform double precision floating point arithmetic which...
Hi all,
I was looking at all ble events and found a few GAP events related to security:
BLE_GAP_EVT_SEC_PARAMS_REQUEST
BLE_GAP_EVT_SEC_INFO_REQUEST
BLE_GAP_EVT_PASSKEY_DISPLAY...
Hi,
I've been monitoring the posts regarding ARM support for the various Nordic tools and libraries - and its been almost two years now since the M1 were released, and still...
I know this should be possible if the phone acts as a BLE advertiser.
But is there any way to scan for a (specific) phone MAC address, if the phone is not advertising BLE...
