Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
in my disc, C:\ncs\v3.0.0 is here. but in nrf extension, weclome page shows the button ("install sdk"). it looks find no sdk. I need set the path to C:\ncs\v3.0.0 (I do not...
Hi，
I am using nRF54L15-DK for Zigbee light_stwitch startup testing. After successfully connecting the development board to the Hub for the first time, I evaluated the time...
Hi.
I made a board with nRF54L15. I would like to use P0.01 on nRF54L15 as GPIO output., but I failed to confirm P0.01 turn high.
Then, I asked nordic AI anything to solve...
Hi,
I generated the credentials as described on the webpage , but az_iot_hub_client_telemetry_get_publish_topic always returned devices/<some garbage characters> and I got...
Hello, For my project I need to control 3 gpios pins. I already found difficult to find gpios that were not already used internally. I decided to use the gpio0 - 8,9,10 they...
My nRF Connect SDK extension in VS Code did an auto update this morning, and now my whole IDE is non-functional.
This is the error I get when I go to the Quick Setup
...
Hi,
I have made a custom board with BL5340PA module from Ezurio and i try to test simple bluetooth advertisement code but i have this error and not able to see my bluetooth...
Hello,
I am developing an LTE-M application on nRF9151, using offloaded sockets to modem, including DTLS.
Everything works great - can connect to network, and communicate...
Hi,
Our devices are running on NRF52833 with soft device version s140. We are facing an issue to do DFU in one particular device. Details mentioned below:
We are able...
Hello,
We run a Bluetooth Mesh network with about 1,000 nodes. Our master node (antenna) consists of:
· An MCU running Zephyr Mesh and keeping the CDB.
· An embedded...
Hi,
We are using the LC3 driver in our product.
We measured the current consumption with and without the LC3 driver.
When the LC3 driver is enabled, the current is 4...
Hi, I'm experiencing a significant performance drop when switching from the nRF9160 to the nRF9151DK.
I have a firmware that sends around 300 kBytes of data over UART in...
Hi, I recently upgraded my nRF Connect SDK to 3.1, and have migrated my code (which was originally based on the direction finding connectionless example) to 3.1 so that it...
Our Jenksing builds when using Nrf Connect v2.7.0, the --no-sysbuild option and CMakePresets worked just fine. When migrating to Nrf Connect v3.0.2 and using sysbuild, they...
