Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi,
We are going through the errata file (nRF52840 rev 2) and wonder how to link anomaly (chip level) with nRF Connect SDK release (RTOS level)...
Where to find the...
Hi!
I am trying to interface LIS3DH module ( https://www.adafruit.com/product/2809 ) with nRF52 DK, SDK 11, via i2c/spi. I tested on Arduino UNO & it gave x,y,z values....
Hello, industry. Two questions for you:
1. To test fault-tolerance of our BLE scanning device we need to generate and advertise from another BLE device custom faulty ...
Hi,
We want to know more about BLE mesh OTA update in Nordic Connect SDK V1.8
Can you please share detail implementation on Firmware Over the air update in NCS 1.8 ...
This might not be the optimal forum for this question, but I'm not sure where else to post it. I have a (I think) very simple question about configuring Zephyr.
I have a...
Hi!
Currently working on a firmware upgrade of nRF91 ns(non-secure) board and build a smp_svr demo from ncs samples found on ncs\v1.7.0\zephyr\samples\subsys\mgmt\mcumgr...
SDK: NCS 1.7.1.
Based on: Peripheral UART example
Central: nRF Dongle
Peripheral: nRF52832
Hi,
I am running into an issue using the "Just Works" pairing method when...
Hi, I was wondering if there is any way to advertise connectable, but non-scannable advertisements.
My device does not have a scan response, but I still see a lot of scan...
Hello,
There is a small problem that I don't know how to solve. I tried looking for it but to no avail. Essentially, my device which runs on NCS v1.7.0 will stop advertising...
Hello,
I am currently trying to record audio using a PDM microphone on the nrf52840 using the nordic PDM library. I have configured the PDM with the default settings, enabled...
nRF52810 SDKs and SoftDevices compatibility matrix does not list nRF52810 SoC revision 2 in the list of compatible SoC revisions for nRF5 SDK. Revision 2 is listed only in...
Hi
I have a machine MacBook Pro 14 Inch 2021
Chip : Apple M1 Pro
I am using nrf52840DK
Using Segger 5.68. installed via Toolchain
Using sdk connect 1.8
The J-Link...
Hello,
We have a head-scratching issue For the sake of brevity, please assume in the following that the definition of "it works" is "the bootloader manages to jump into...
Hi,
I'm trying to interface Adafruit 9-DOF Absolute Orientation IMU Fusion Breakout - BNO055 sensor with nRF5340 DK board. Can you please help with the code where I want...
Hi,
I installed NRF connect SDK,
after installation I navigate from NRF connect desktop app -> Toolchain Manager
V1.71 is installed in D:\Nordic_App\Nordic_SDK\nCS...
