Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi,
I am using AFE4403 and Nrf52840, I want to assign a pin as output oscillator 4M using a nrf52 internal oscillator,
how to do that?
I am beginner , is my first...
Hi Everyone,
I'm not able to start ble scan. I've followed following example...
Developing Bluetooth Low Energy products using nRF Connect SDK
https://www.youtube.com...
Hello,
I was trying out sending RR intervals on the Heart Rate Measurement service and seeing what happens in nRF Connect. But, something is weird with the way the values...
I have a client project developed in 9160 which needs to be connected to the network via NB or LTE-M. Before each connection, I read imsi to determine the apn of the carrier...
Hi
Im trying to get the mcp2515 candriver example to work https://github.com/nrfconnect/sdk-zephyr/tree/main/samples/net/sockets/can#id3 .
i have some error during build...
We have an nRF52 with dual roles: peripheral for the connection to an app, and central, connecting to multiple third party peripheral devices.
We have come across a very...
Hello,
I'm using Segger Embedded Studio (SES) (on Windows 10) with nRfConnect SDK and nrf5340 processor.
In SES I can oben a graphical view of the configuration through...
Hi, I have developed a firmware on nRF52840 as central ble_app_uart_c\pca10056\s140. Now I have to upload it in nRF52810 which soft device should I use? Thanks!
Hi all,
I working with NCS v1.7.1 on a custom board using nRF52840 and I am trying to enable a 2-stage bootloader setup using NSIB as the first stage immutable bootloader...
Hello sir,
I am using the nrf52832 Dev board and try to send the data through custom value update then the following error occurs as ERROR 8 [NRF_ERROR_INVALID_STATE].How...
P0.25 is accessible by below:
nrf_gpio_pin_set(25);
However, when I try to access P1.00: Neither this:
nrf_gpio_pin_set(1); Nor this works:
nrf_gpio_pin_set(32);...
Hello, we have a device that uses the nRF9160 with an external GPS receiver that is controlled over I2C. I have connected the LNA enable pin to COEX0 on the nRF9160, but it...
Hi,
I was evaluating 9160DK. I tried the GPS example using 1.7.1 SDK and it works great outdoor. However, I tried to use a hackRF one to emulate the GPS signal. 9160 shows...
Hi
I still have a number of devices that are based on nRF24E1. From time to time the chips need a change in firmware. Since the last time I updated them, my PC has crashed...
