When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hello,
I've been trying to access the nRF52840 dongle through the pc-ble-driver-py library. However, I can't get the Nordic examples to run. Here's what I did so far:...
I want to send my sensor data from one node to another node using BLE mesh. my data is at about 128 bytes I am trying to create a custom model but it's hard to know how to...
Hello, I am trying to advertise twice in my project with different gap_params.
First, I have started advertising with the following conn_params (shown below)
#define MIN_CONN_INTERVAL_ADV...
In a old post https://devzone.nordicsemi.com/f/nordic-q-a/58034/uart-communication-between-nrf52840-and-nrf9160-on-nrf9160-dk This question was already answered but this solution...
I am now using nrf52840 dongle and want to develop a software to control dongle like NRF connect desktop software, such as scan devices, connect device with passkey, read...
Hi
I am interesting to generate 1,638,400 Hz is an external clock for a peripheral on one of the NRF pins.
Please advise how can I generate this clock value on one of...
To the kind attention of Nordic support team,
We have this custom board using nRF52833 powered up from usb and in high voltage mode (ldo). The problem is that we are...
VS Code (running on Ubuntu 21.10) can't find the connected nRF52840 dev kit. " Could not find any connected boards " is all that's shown under CONNECTED DEVICES. Beside that...
I'm learning to use the Asset Tracker V2 example and planning to build a POC product on top the example. The biggest issue at the moment is with power consumption. On the...
To the kind attention of Nordic support team,
We have a problem that may very well be linked to this thread
https://devzone.nordicsemi.com/f/nordic-q-a/65202/usbregstatus...
Hi, I got my border router working fine, but I do not understand its use. How can I connect (which kind of protocol?) with the nrf5340 from my laptop to send turn on a led...
Hello
We check the current in system off in PCA10059 board. and use the ble_app_template application.
If set the VDD 3.3V, after the system off, measure the current is...
Hi Team,
I want to connect power pins on the nrf52840 chip in the schematic.
I find there several VDD pins, how can I select and connect them?
Best,
Gaosheng
Hello,
we are currently developing a customer product based on the nRF9160 SIP.
The requirement is to send the battery voltage periodically over the CoAP protocol (PUT...
