Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi,
I have used "es_battery_voltage_saadc" in SDK 14.2 to read the voltage of battery, now I'm using SDK 17.02, but there is no es_battery_voltage_saadc.
Is there a better...
Hi
For the revision 3 of the nRF52832, I've updated to the nRF5 SDK V17.1.0 to apply the workaround for erratum 249.
Afterwards, I saw that there is a newer version of...
I have a BLE peripheral device using i2c, gpio. When the peripheral is not connected I want the lowest power consumption possible.
when i try to turn off gpio:
//sleep...
Hi Nordic.
I am using:
1. Mesh sdk V5.00
2. BLE sdk V17
3. NRF52840
I am trying to build a node with many elements and models. The software is based on the LC server...
A question regarding to nRFSDK 1.7: why does nRFSDK disable using BL2 inside TF-M? If our device needs BL2 with TF-M, how can we enable it? I can't enable CONFIG_TFM_BL2 if...
Hi Everyone,
I was wondering if it is something I do wrong, or if there is an issue with my module.
I have never managed to successfully upgrade the firmware of my nRF9160...
Hi,
is it any possibilities to multilink central with s112 in nrf52810 chip?
using sdk: sdk14
actually, i am using sdk14 with one central and one peripheral is fine...
Hello, All,
When using UART on nRF Connect SDK to communicate between nrf9160DK and nRF2833DK, I found that the data length of a packet sent by the UART on both sides is...
Hi,
I have started a new project that will use I2C and SPI devices. As a starter I took the example at /examples/peripheral/gfx/pca10040 since I am using a ST7735 based...
Hello sir,
I am using nrf52832 as Dev kit board with using Button 1 for long press event for an interval of 5 sec .I have defined the BT0_LONG_PUSH as BSP_EVENT_KEY_0 which...
Hi,
I'm trying to build the Zephyr NVS sample in SDK 1.6.0 and SDK 1.7.0 for nrf9160dk_nrf9160ns (Non-Secure) and build operation is failing with errors.
../src/main...
NCS V1.7.0
VSC IDE
In VSC you can create a custom board.
when i do this for the nRF5340 and build, it does not include the network core.
it also does not appear...
Hello
in order to reach low power mode I use the following :
bsd_shutdown(); // 3.4 ma.
nrf_regulators_system_off(NRF_REGULATORS_NS);
how can I recover from...
Hey,
I have a custom board that is pretty much the same as an evaluation board I got. I use the secure_bootloader_uart_mbr_pca10056 to enter and execute a DFU.
On the...
Hello,
I tried to check SPI communication with a test board.
However, I couldn't read the device info from the max30003wing board.
Board: NRF52840DK --> MAX30003WING...
