Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
The first chip silkscreen for 2050ST ,second chip silkscreen is 2109XN ,third silkscreen is 2052TJ, transmit power configuration for 8dBm actual test from the chip side, test...
Hello,
I'm trying to flash a nRF52840 board (Particle Xenon) with nRF Connect for VSC on macOS.
macOS Big Sur 10.16
Here is my nRF Connect - VS Code environment: ...
Hello,
I am using multiple ADC pins and realized that repeated calls to the ADC give inconsistent data, suggesting that the conversions are not completing before the next...
As far as I understand at the moment only proprietary solutions are available for Mesh DFU and Remote Provisioning.
I assume that Nordic is working on standard solution...
Hello,
After looking at the schematic of the nRF9160 DK and the Thingy:91, I noticed that for the nRF9160 DK there is only one antenna design for LTE, while for the Thingy...
Hello,
When I attempt to download the zip file with title: "nRF ready Smart Remote 3 for nRF52 Series firmware files, version 1.2.1.alpha" from https://www.nordicsemi.com...
Hi Team,
I have a few questions regarding nRF5 SDK and nRF Connect SDK.
I have previously used nRF5 SDK for two years, with and without freeRTOS. We might be making a...
Hello Devzone Community,
I am trying to incorporate Nordic's version of Segger Embedded Studio, SES v5.60 in Zephyr based firmware development for the nRF9160. I've cloned...
Hi, Im trying to get the debugger working in VSCode using the new nrfConnect for VSCode, while following the Youtube series for nRF Connect in VSCode. Im using the following...
When compiling the sample located in samples/subsys/nvs/src/main.c I get the following compile error:
I tried to revert the last commit and manage to compile and run the...
Hi DevZone !
I have a problem with the FDS library. I am using it to store configurations of my nRF52840 that I read every time the chip resets I will write in that only...
Hi,
I have a nRF51822 evaluation board and a nRF52833 DK.
Would it be possible to do Bluetooth direction finding with both of them?
I understand that nRF51822 is not...
Hi,
I am trying to measure my circuit sleep current while connected, through a high value resistor, the problem is while waking up each MIN_CONN_INTERVAL the processor wakes...
It is found that under the same routine in zigBee SDK, the project under pCA10056 folder can run normally without burning the protocol stack, but the project under PCA10059...
