Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
I'm putting together a prototype using the nRF52 DK and the Adafruit Sharp Memory LCD board. I need to send SPI commands to communicate with the display.
I've installed...
Hi,
I tried to run a quick test to see if NVS functionality works out of the box when adding it to the tfm_ipc sample in Zephyr and it seems that my call to nvs_init hangs...
Hi Nordic,
I've tried to do some long duration measurements first 5 days, but also just 24 hours. Both times the Power Profiler desktop app was still running when i came...
This is just general feedback about the Infocenter documentation. When multiple tabs are open, or for bookmarking purposes, it would be nice if the webpage title changed to...
Hi We are developing a project where we are using a peripheral over i2c, specifically a lis3dh accelerometer. However we have encountered a problem and would be really grateful...
I want to set more features in a single service, but once there are more than four features, some features will fail and no error will be reported. Some features in the service...
Hi suport team
1、My ADC sampling circuit is shown in the figure below.
2、The actual voltage at ADC sampling is 1.37v, but the voltage measured by ADC is only 1.29v....
After programming the sample to my nRF9160 DK, I opened the terminal emulator and I observed the following messages:
1. HTTPS client sample started
2. Provisioning certificate...
I have tried the nus relay experimental example using nrf52dk and sdk 17. However it crashes when I try to connect using either nrfToolbox Uart or BlueFruit Connect (Uart...
Hello. I'm sorry for my bad English. I'm currently working on a development using nRF52840 based on ble_app_blinky, which is an example of s140 and peripheral. So, I want...
2. In the nRF sniffer software, the device I'm interested in does not show up in the "Source" column with its addess, b8:80:4f:6b:b6:9e, but as "TexasIns_6b:b6:9e". It seems...
Hello,
I'm finding problem to generate the library uECC.a to use in project secure_bootloader for nRF52833 (SDK17) using SEGGER.
I started from project SDK_17\examples...
i want that my device shall advertise after i press a button for 5 seconds. there is a feature of long press for button kindly assist as how to use this for advertising
Hello,
I am currently trying to combine the NRF52840 (Development kit) with the Arduino Ethernet shield containing an W5500.
I was wondering if there is any example...
I have been trying to figure out how to use SPI on nRF Connect SDK. I cannot find a simple enough example to get started other than the convoluted SPI flash example or the...
