When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
hi,
For NRF52840, is the 125kbps sensitivity the same as on Radio? I used the 125kbps long distance mode, but the distance was not up to the ideal state, the deviation was...
Good morning,
I'm developing an application for nRF52805.
I saw that in SDKFolder/config there are all "complete" sdk_config.h files for all nrf52 targets except for the...
Hi,
I am using own hardware board based on https://www.raytac.com/product/ins.php?index_id=24 module, it uses nRF52840.
I
I am facing an strange issue that UART is not...
Hi,
can anyone provide any insight into moving beyond a pca10040 development board and creating a project for a custom board? What are the steps that you have to go through...
Hi,
We are looking to be able to reflash our devices on the field, as well as do FOTA. Critical device information (serial number, encryption keys, etc) are stored in the...
How does the ADC gain block work.
Suppose using Vdd=3.3V as ADC reference, analog signal input from 0 to 3V and gain 1/4
What will be the ADC core voltage for single...
I have an application where i have to regularly send gps data to an mqtt broker. I started with the mqtt sample which works fine, and i also tried the gps example with assited...
Hello,
I am trying to extract audio from the thingy's microphone using the microphone driver. I know that the data it produces is encoded in dvi_adpcm. I would like to decode...
Hi,
I am using nrf52833 development kit and using nRF5 17.2 SDK on KEIL IDE with softdevice as S140.
I am trying to compile ble_app_template example from the peripheral...
Hi Iam using NCS version 1.5.0 and DK version 0.15.0
Is it even possible to perform FOTA over SMP BT on NRF9160?I am using 840 as my controller and normal ble functionalities...
Hi,
I'm developing a system where I have a two button "remote" and connecting to movable part that plays sounds. My plan was to have a nRF52 in each of the parts. So ...
1. Can nrf9160dk protect code avoid any one to read firmware out and copy them in usb 2. Can nrf9160dk protect code avoid any one to read firmware out and copy them in externl...
Hi All,
I have 2 boards nrf52840 pc10056 and I need to run ble_app_uart using LIBUARTE with DMA in order to obtain a more robust uart communication
I would like to use...
Hi
This is probably not specific to Nordic, through talking about a beacon-type device based on nRF52 chip. The purpose of the beacon is to advertise its presence and once...
