Hello,
I would like to develop a custom key sharing algorithm for nRF8001 chips. As far as I have understood the only way to use full 128-bit temporary key (TK) is OOB...
i am useing nRF51822 pairing with nRF24lu1 over GZLL protocol now,
is there someone have the experience on how to config the parameter of GZP_TX_RX_TRANS_DELAY in function...
I have a peripheral running the S110 stack, which presents a characteristic to which I want the central (running S120) to be able to do a long write. What I've been trying...
Hi all,
I have been trying to combine the UART and hID Keyboard examples into a single application.
I want to use the HID part to send specific keystrokes using buttons...
Hi, I'm new to BLE and just started feasibility testing, using RF8001, on a small device with no IO. The device will have a unique code set at factory, and printed on label...
I had the same experience as fishman and I went back to give Eclipse a try. (Post: nRF Beacon does not build on Android studio) I tried to build it in Eclipse Luna with the...
Hello, I just got an nrf9160dk with hopes that it would allow me to reprogram a Thingy91 that I couldn't program through the MCU method. (this is an still open ticket: https...
I use nrf5_SDK_for_Mesh_v3.2.0_src\examples\experimental_lpn and board PCA10040.
When I close main.c ERROR_CHECK(sd_power_dcdc_mode_set(NRF_POWER_DCDC_ENABLE)), nRF Mesh...
Hello,
I'm started implementing DFU over serial port and see documentation from this link: https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter.sdk5...
Hi, I am now using nRF24lu1p, for using cklf_wdog_init() to enable watchdog, then I set cklf_wdog_init(10) in main function, but don't know how to set watchdog event handle...
So we have been developing on the nRF52811 and realized we need OTA (Over the air Frimware) aswell and we have 30kB Flash and 8kB Ram remaining. Can this be done?
Also a...
Dear Sir/Madam,
I am trying following,
1. Avoiding SPIM transfer interrupt handler.
I am performing following steps,
1. nrf_drv_spi_init() for Handler parmater 'NULL...
Hello,
I'm using nRF connect for power profiling of nRF52840 DK. First time it works.
If we close the nRF connect and open it again then I get error.(Also after power...
How can I do LESC on my central with an Android peripheral device, if with each new connection the MAC address on Andriod changed randomly?
The first time I am making a...
Hello,
I want to use 100 bytes of flash as non-volatile data memory. We should be able to read and write this memory during execution.
So for this purpose I need the implementation...
I already follow the link for terminal in this link https://infocenter.nordicsemi.com/index.jsp?topic=%2Fsdk_nrf5_v16.0.0%2Flib_cli.html&cp=6_1_3_10_3&anchor=lib_cli_terminal_settings...
nRF52DK
p20 debug out
external board is 51822 + sensors
I managed to connect the external board through p20 on the 52DK. I can successfully program the external board...
I am reading about nRF52811 SoC which is currently supported by nRF5 SDK v15.3.0 and SoftDevice S112.
I want to know more about its direction finding capabilities and play...
Hi,
I'm trying to add the NUS service to an existing application (freertos based, SDK15.2, already use a custom service)
I copied the relevant code snippets from...
Hi everyone,
I'm trying to use nRF52810 with SoftDevice S112 to sample five ADC channels. I'm finding this very weird issue, where first channel is showing correct value...
