Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
hi,everyone
when i test the mesh/example/dfu , it is upgrade scucessed,but when i combine it to switch_light example ,it was failed , it looks end the transfer too early...
Hi, there~
I'm trying to make my own bootloader and starting with the secure bootloader sample code.
The problem is the orignal bootloader, that is compiled with secure...
Hello,
Recently I started working on BLE. I need details with respect to BLE 5.0.
Below are the features of BLE 5.0
2x Range (With 2Mbps PHY)
4x Speed (With...
Hi,
I've created 3 PWM pulses via:
Which works when I'm not starting Thread (from the examples/thread/freertos_coap_server example)
But when I start Thread...
Dear Sir,
I am working on the following scenario.
I have BLE device ( SDK 15 and softdevice s132). It is advertising for specific duration.
There are different phones...
Hi,
I am working on a project where I am sending and receiving Encrypted string data from my phone with nRF Toolbox to the nRF52840 DK. The basic paring is established along...
I recently got past an issue with not connecting to the LTE network getting an nrf_cloud_connect failed: 60 and had things working yesterday. I had support for that issue...
Hey, I'm trying to connect a touchscreen monitor (10 finger) usb into a computer, get a raw input report and send it over uart to bluetooth module and sent it to other computer...
In IAR it shows the cycle count registers and they appear to work as expected in that view (shown as CYCLECOUNTER) . In the IAR Project/SFRSetup it shows the address of DWT_CYCCNT...
Hello,
I am developing a simple HID device with output report to receive data from PC. I took keyboard example as base project and I want to increase output report size...
Hello!
I have a custom nRF52832 board with an FTDI usb/serial part running my app successfully.
I generally program the board with a JLINK and SWD, but I am working to...
Hi, I apologize for the question renewal, that is the same as ticket "SDK15 DFU and WatchDog issue" (for my mistake I closed the discussion post!). I have developed a custom...
SDK 15.3.0
I want to save some user data in UICR , this data will change when application runing. How to re-write the data into UICR.
I assume that the UICR will not be...
Dear sir,
I have merged the twi_sensor code in ble_app_uart code in order to read the temperature sensor MAX30205 with NRF52832 send it over Bluetooth. But I am getting...
