Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
My work need to use 4 gpio interrupt, but it not work when use freertos on nRF52832 ,sdk version 15.0.0. My code is like below:
err_code = nrf_drv_gpiote_init();
nrf_drv_gpiote_in_config_t...
I created own app button library. It's just return handler into main with number of pin and type of push - short or long. Also I created library for rgb_led (using nrf_pwm...
Hello everybody,
I'm using nRF5280 (Laird BL654) with SoftDeveice S140v6.1.0 and SDK 15.2.0 with a modified version of the blinky peripheral example.
I've changed NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
Hello
Our custom board has two chip configurations for BLE stack. The two chips communicate with each other through UART. Both chips are running zephyr with two chip configuration...
I'm writing an app to that talks to the Thing52 over BLE, and using this as a reference: nordicsemiconductor.github.io/.../firmware_architecture.html For Battery Services...
Hi,
We just recently bought the nRF9160_DK board and compiled and loaded the AT_Client onto the DK. We have followed all the setup instructions for the SIM card for iBasis...
The example code of beacon was used from the SDK - nRF5_SDK_12.1.0_0d23e2a\examples\ble_peripheral\ble_app_beacon\pca10028\s130\arm5_no_packs\ble_app_beacon_pca10028_s130...
Hi experts,
Currently some issues are found in zephyr os, especially the precision of k_timer. Since the nRF51 series uses RTC as the system clock on zephyr os, the round...
I use the scheduler. All my idea is put an event in interrupt handler(timer event, gpiote event and so on) and schedule it to main loop to let app_sched_execute to handle...
Hi All,
We're designing Legacy/Coded Phy scanner based on nrf52811.
The existing softdevice that supports Coded Phy scanner is S140.
Can nrf52811 work with S140 or Nordic...
Hi,
I am struggling with recconecting to Android device. I want the project to work with iOS also.
My nRF de52832 device has got peripheral role in this project. I am...
Hi team,
One of my customer is evaluating nRF52840 running ANT networking, but they may encounter with connection distance issue and wondering if they can combine BT5 long...
Hi,
I just installed the latest nRF Mesh v1.2.1 and found that my nRF52840 DK board unable to connect,
I'm using SDK as shown below:-
nRF SDK for mesh v3.1
nRF SDK...
Hello,
I need to get access to nRF51822 pins in order to test them and connected circuits.
I have access to SWD interface only.
By attempt to read ID register (A2=0...
Hey,
I am running the ble_hid_mouse example on the nRF52832 with SDK15.2 and connected a joystick to replace the buttons commands. now i wanna use the nRF52840 as a slave...
