Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hello,
Now i use NRF51822 DK with code in attachment to test app_timer hangs.
Fristly , you can press button 0 to start a 100ms app_timer, and we can see it through uart...
I am attempting to use Enhanced Shockburst/Gazell working with coded PHY, in order to achieve long range communications with very lower power consumption. I have searched...
Hello, I am experimenting with your nrf5SDKforMeshv310
I can compile and download the included examples.
Because I own a few Thingy 52, I wish to flash them as light_dimming_servers...
hi,
I am trying to add SPI (master) codes into the ble_app_uart.
My setting for SPI is as follows:
#define SPI1_ENABLED 1 // #define SPI_INSTANCE 1 /**< SPI instance...
Hi I am using nRF52832 board amd i am trying to debug ble_app_uart as Central.
BLE connection is established between this central application and the peripheral.
Opened...
i am using nrf24l01+ on arduino devices, one arduino device as master, and other arduino devices as slaves. I like master to broadcast a radio (dataToSend) toward all slaves...
nrf52832, keil with startups from sdk13
Initialization:
IntHandler:
With one event everything working well. Then I add another:
I need to measure SENT signal...
hi.... folks
i am using nrf52840 development kit , and i debugged the merged programs such as uart and twi program in it .does it will give the temperature data?
i am...
Hi all,
Please refer to the SDK version : nRF5_SDK_15.2.0_9412b96.
We need to use two uarts simultaneously for module & device respectively.
For example :
UARTE0 ...
We, I am using nRF 5 SDK v 14.2.0.
Power-off has occurred during program development. I can not identify the location, Functions that are not memory leak, buffer overflow...
Hi,
Now, I am using the nRF52840 to develop and do signal test. Can you share me some tool that can make the board enter the test mode?
Best regards
Simon
Hi:
PREJECT: nRF5_SDK_14.2.0_17b948a\examples\ble_peripheral\ble_app_hrs_freertos\pca10040\s132\arm5_no_packs
When TWI0 and GPIOTE are turned on at the same time, the...
I'm trying to get the AT commands sent in the asset_tracker example written out together with the other printk statements. I have tried adding this to the prj.conf: CONFIG_LOG...
I used the nrf52840 as the central device, use SDK15.0, scan then connect the peripheral toys.
sometimes i found the central can scanned some ble peripheral but can't connected...
