Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
HI
In the case the keyboard miss the LTK(or bonding info), how can I start a reconnect or re-authenticating to let the host and device to generat a new one?
When I replies...
I'm using the nRF51822 as SPI slave. My CSN is of wrong polarity (active high). Is it possible to change the settings in spi_slave.c to make it work anyway?
HI
when i use 51822 connect to a host like iphone how can I get the host 's Ver info?
As I know there is a function to get local version info:sd_ble_version_get
and I do...
Using:
nRF51822 (nRFgo starterkit with nRF6310 and PCA10005)
Softdevice s110 version 6.0
Nordic Sdk 5.2.0
Compiled with GCC 4.8 using pure-gcc setup
I...
Is it possible to whitelist a private resolvable address without bonding, or is bonding required? I want to limit reconnection to the same central after it disconnects, but...
Hi,
I'm using the makefile from ble_hrs to write my own makefile. I need to had libraries .lib and .a files.
How should I add my files in the makefile?
Thanks in advance...
hi. dear.
I have custom board using the NRF51822 - nRF24LU1P.
use the gazell protocol.
I want to unencryption key data.
Plz, tell me how to use unencryption key data...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
I have an issue with the ble_app_lbs. I can compile it OK, but when I run it it gets as far as calling sd_ble_gap_device_name_set(), which returns error 0x3001.
Can someone...
Im writing a serial bootloader for the NRF51822 128kB. Im not using much of the SDK and its a custom protocol i.e. no bluetooth. The boot loader can be squeezed into 16kB...
I looked at a very similar thread that had this title for MacOS and I feel that my issues are the same however changing the hardware debugger only changes the error I get...
Halo, is there any linux ( possibly debian or even better raspbian ) driver for
nRF24AP2-USB dongle?
Do you have ANTware II linux ( possibly debian or even better raspbian...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
I'm using Keil to debug my application. Softdevice was loaded w/ Studio and when I click on Debug Keil loads the code but it does not stop at any breakpoint I set. It does...