I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
The question is as follows：
When I read the ADS1299 data through SPI in the GPIOTE interrupt, I found that there was a time limit. Within about 50us. As shown in the figure...
Good morning
Doing the BLE fundamentals course and cant seem to build lesson 4 ex 3. Have picked up this thread BLE Fundamentals lesson 4 exercise 3 failure to build ...
Hello,
I have started working with the nRF54H20 by following the guidelines mentioned in the nRF Connect SDK Fundamentals course.
In Lesson1 Exercise2 I'm facing following...
I'm using the Thingy52 circuit in some other projects, and the built-in speaker is not loud enough for my application. I'm looking for an amplifier that can be connected to...
Dear,
We are currently developing a communication board for a client that uploads large images (~1MB) to the cloud via local and remote interfaces, and we've encountered...
Hello! I'm currently trying to scope out chips that let me do Bluetooth Classic + BLE via a UART HCI link. I came this module and noticed that it uses the NRF5340.
NORDIC...
Hello everyone,
I'm currently working on a project wherewe use the ANNAB402 and Zephyr as out RTOS. We are developing using VSCode on a Linux VM. With a new board from us...
Hi ,
I am using nrf52840 as a peripheral HID Remote control with multi-connections, and it is able to connect with all devices like phones, computers, smart televisions...
The out-of-box configuration of Thingy 52 has a 89dB, 8 ohm, 0.7W speaker.
Can I replace that with a much louder speaker such as 4W or 5W one 4 ohm or 8 ohm?
44
I am programming with the nRF52840DKs. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am currently working on integrating...
Hi,
We're currently facing an issue with Bluetooth Low Energy (BLE) range on our custom board using the NRF5340 with SDK version 2.6.1. During testing, we observed a significant...
We are migrating the firmware of our devices from Nordic's Mesh SDK 5.0.0 to Zephyr 3.5.0, starting with the provisioner device. The SOC we use is the nrf52840 and we use...
Hi, do i need to place external hardware (antenna ?) in order to be able to read the NFC info of the board?
According to the peripheral_hids_keyboad sample:
"When the...
Is it possible to enable and disable the ADC peripheral of nRF52840 to save power in nRF connect SDK? In our application, we use ADC to get battery voltage samples after every...
Hello,
I have the task to persistently store some (2) configuration values in a Zephyr application (Nordic Version). The final version contains some external flash memory...
