hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hello,
I am trying to get the RSSI value of a connected device on the nRF54L15, the same thing with our nrf54H20 device (nRF54H20 would be great if i can retrieve it via...
I am curious about the RF pin impedance, as this parameter is not listed in the relevant specification for nRF54 SoC family (i.e. datasheet v1.0).
I wonder whether it is...
Hi,
To improve the accuracy of RTT-based ranging measurements, the Bluetooth CS specifications requires that the initiator compensate for the fractional frequency offset...
We are using QSPI to connect nrf52840 DK with nand flash of AS5F34G04SND. In page 28, 29, and page 17-table 2-1 of datasheet of the flash, we need to Program load x4 IO: sending...
I am on a custom NRF54L15 module where I want to change the default UART TX pin from P1.04 to P2.07. Unfortunately, there is no output. Using P1.14 somehow works? I also have...
Using nrf connect 3.1.1
using nrf54L15 evaluation board.
Hi,
I have an application that is using the shell capabilities of the zephyr. uart and shell is connected...
Hi,
using nrf connect SDK v3.1.1
using nrf54L15 development board.
I have been trying to return set uart in low power mode and resume uart low power from a button press...
Hi, I interfaced the Quectel EC200U GSM module with the nrf5340dk. Now I want to do the FOTA with the help of GSM . Is there any example documents or any experince. And also...
I am trying to make the nrf9161 go to very low power mode for 10 seconds and then come back online.
Actually I would not mind if it were to start all over again when coming...
Hello,
I am using the example on the Nordic DK to get UDP messages from the Hologram API to the Nordic Modem. AT#XUDPSVR=1,6002 #XUDPSVR: 3,"started" OK
I very inconsistently...
Hello,
I am working with the nRF9151 board and trying to read SIM/eSIM information.
Steps I followed:
Used nRF Programmer → Erase all.
Opened Board Configuration ...
Dear Nordic
We are evaluating a wearable device and plan to use nRF54H20 be our MCU,
Since our device will be a small form factor and Nordic not released datasheet yet...
Hi, I'm working on nRF9151 on custom board, NCS 3.1.0 and I'm building application with TF-M enabled. I've encountered quite a strange problem. If I remove all UART instances...
