When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi team,
Please find below logs. While programing this error occurs. please find the logs and do needful. Earlier programing happens now it's not happened. Based on below...
I have an application with a shipping mode that when enabled/disabled calls `conn_mgr_all_if_connect/conn_mgr_all_if_disconnect`. These functions eventually end up in `lte_net_if...
Hi,
While testing, I ran into multiple problems when measuring the current consumption with the PPK 2 on the nRF52833 dk.
For all measurements the Blinky + Bluetooth demo...
Hello,
I am using WM02F WiFi mdule with nRF7002 SoC and i am having some issues with the TX power measurement of the WM02F WiFi module while operating it in 2.4GHz.
I...
Dear Nordic team,
We are a medical device manufacturer company in Australia.
Currently we are developing a medical device system, the system compose of a base station...
In developing project firmware uses bluetooth shell and one command outputs many lines.
It works fine. Unfortunately, firmware locks up after phone BLE app disconnect in...
Hello, we want to evaluate the BLE ISP2454-LX chip.
To do this we bought from RUTRONIK FRANCE an ISP2454-LX-EB evaluation board with the ISP2454-LX-TB test board.
SDK...
Hello,
We are currently evaluating BLE Gateway (CIS, BIS) development using the nRF5340 Audio DK.
We would like to ask whether bidirectional CIS streaming is officially...
I am using nRF54L15-DK, I choosed the CONFIG_NFC_T2T_NRFXLIB=y.
In this case, I get tag type ISO 14443-4.
But what I need is ISO 14443-3A.
The following is my nfc_init...
Hi,
I'm developing with NCS 3.2.4 and want to expose the Zephyr shell over BLE using NUS (Nordic UART Service). I've identified two possible starting points and have a couple...
Hello, we want to evaluate the BLE ISP2454-LX chip.
To do this we bought from RUTRONIK FRANCE an ISP2454-LX-EB evaluation board with the ISP2454-LX-TB test board.
SDK...
Hi,
I see the different behavior of the function sd_ble_gap_conn_param_update when connected to Windows integrated Bluetooth.
Using bare-metal SDK v0.9.0 it succeeds...
Dear Everyone, SDK 3.3.0, Board: NRF54L15 We have integrated MCUBOOT into our project. We have image built for two slots and we can see that it works once uploaded by VS-Code...
Developing an implementation for UltraWideBandImpl for a different UWB hardware solution (not the provided qm35 implementation) and running into integration problems
The...
