Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hello everyone,
I am designing a Bluetooth repeater that will be powered eather by USB or an embedded Li-Po battery. This device will run with the nRF52833 along with...
Hi,
I am working on a project, where I am trying to create a touch LED project using NRF52832. I have completed the prototype, its working is quite simple. The LED will...
Hello, guys!
We are using nRF51822 SoC with nRF5 SDK v12.3.0 and s130 SoftDevice. One of our desires is to use Software Interrupt (SWI) driver.
However, when I try to...
Hello all,
I am configuring a low power application for the nrf52832 board (custom board). This is a very low power application and I want the board to stay on sleep mode...
Hello everyone, I am working with a BMI160 6-DoF sensor. I have some drivers related to this chip. Using the Segger J-Link debugger the drivers just work fine without any...
I update a couple of device to mfw_nrf9160_1.3.2.zip.
Before that (1.3.1), my experience was to get a ENETDOWN, when calling " sendto" while the device has lost some the...
Hi.
I'm trying to add Bluetooth capability to the "Asset Tracker V2" project. I was able to do it on the nRF9160DK board. I could not find a working example to make the...
Hello,
windows10 x64.
i have used NCS1.9.1 and NCS1.9.99,now i want update to 2.0.99
how to install NCS2.0.99?
because nRF Connect for Desktop Toolchain manager no...
Hi,
1. How to calculate the Flash and RAM usages at runtime? I am able to do it static way but wanted to analyze this at runtime.
2. How to calculate the Heap usages at...
Hallo,
currently I try to optimise the functionality of my extended advertiser code. I found that there are also some call-backs defined for extended advertisers. The struct...
I use iOS nRF Connect APP to test DFU. But it failed with writing is not permitted.
The following is log message of nRF52832 device. 00> <info> app: Inside main 00> 00>...
Hi,
I am working on a system that runs a proprietary protocol, i.e. non-BLE, which works fine when it uses either uncoded links or S=8 ( LR125Kbit ) coded links, but I want...
Hello everyone, I am trying to send a string printed float number using the ESB protocol. I am using nrfConnect SDK 1.9.1 with nrf52832, started off with the supplied esb_ptx...
Respected,
I am using NRF connect for desktop for programming my actinius sensor (ICARUS IOT BOARD) but whenever I want to upload and reset the board using actinius programmer...
