Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi,
I'm using Linux with Visual code extension to compile for both nrf52840DK and nrf52480 dongle and I'm using the programmer in nrfConnect to write to the devices. The...
This case don't happen when i merged net_core and app_core to burn . I used to burn only one core.
What causes this?
Now I have a new question.I use one nrf5340 as CIS...
I am using nRF connect SDK and wanted to examine gpio 'out' register during the debugging session but every time I try to print the register value, I get the following error...
Hi,
I am using the SDK 2.1.1 and I will upgrade to 2.1.4 since errata 160 is fixed there.
Reading the errata document here , the anomaly 168 is fixed in SDK 2.5.1. Unfortunately...
Dear nRF support,
nRF5340 custom board
nRF NCS 2.5.x
Running into this very weird issue:
Program runs fine if I don't attach debugger to it
When I do "attach to...
Hello Nordic Engineer,
I successfully controlled the 52840 DK through Mesh using my phone. However, after exiting the app and reopening it, I can no longer control the...
Hello Team,
I’m working on implementing BLE Mesh on the nRF52832. I extracted the BLE Mesh ZIP file and placed it in the same directory as the nRF SDK. Then, I opened the...
Dear Nordic Support Team,
I am encountering an issue with the nRF52 SDK for Mesh v5.0 and nRF52 SDK v17.0.2 while running the serial example. The system runs for a while...
Hello,
In the header file nrf54l15_types.h, we see the following defines related to the SAADC:
* REFSEL @Bit 12 : Reference control */
#define SAADC_CH_CONFIG_REFSEL_Pos...
Errors on calling "lte_lc_init()"
Does anyone know what the corresponding error codes mean, or what could be done to debug the cause?
Thank you very much.
I am writing an i2s application for the nRF5340 Audio DK with toolchain and nRF Connect SDK v2.9.0.
During development I noticed that nrfx_i2s_start() does not seem to check...
Hi,
I am working on a project where I have two separate physical devices , each based on an nRF52832 :
One device is a BLE Mouse
The other is a BLE Keyboard
My...
Hello, lte_ble_gateway works ok using dk91 or thingy:91 on, v251 - ok v262 - ok but not on, v270 - err v280 - err v290 - err This is straight example code as found in VS....
Hi Team,
I need help currently we are using nrf52833 micro controller, we have problem with external clocks. we want to disable external 32Mhz and 32khz clocks and use only...
