hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hi, I want to be able to send 1bit of data with as low latency as possible, what is the best way of doing this? Can i in some way directly control the low level of the radio...
Hi All,
i am using the below link to flash the bootloader
https://devzone.nordicsemi.com/guides/nrf-connect-sdk-guides/b/software/posts/device-firmware-update-dfu-with...
Hello,
I am using Eclips & ARM tool chain for project with BLE functionality. I tried to import this code in Segger embedded IDE but it did not worked. This project is old...
Hello,
I built peripheral_hr_coded sample and looking into the partition manager report (I trucated the output):
What are the s0_pad and s1_pad?
What are the EMPTY_0...
Hello,
I am developing a FreeRTOS project that uses nRF5340 MCU. For the inter processor communication I would like to make use of the RTOS-agnostic RPC library (sdk-nrfxlib...
Hello fellow bit jugglers!
We are developing an application for a nRF52805 on a nRF52-DK board, using NCS.
NCS version: 1.7.1
Zephyr version: 2.6.99-ncs1-1 (commit...
Hi:
I have a BLE HID remote control that needs to be connected to the HID central(nRF52832).My SDK is NCS v1.8.0.
When I try to connect with the HID remote I get the log...
Hello,
I have to make the external flash on the nRF9160DK work with the nRF9160.
From what I understood, the default settings are that the external flash on the board...
I have beacon that broadcast its name with type 09. I cannot get it while scanning of nrf_uart_c (adv_report).
I assume I need to activate scan_req and then parse the response...
I need a constant acquisition time for my SAADC. In my experiements I see jitter in the acquisition time, so I started debugging with PPI to ensure no Interrupts are making...
Hi,
I am trying to enable event length extension on uart example provided on the sdk. I look for information on how to done it and i found links like that:
https://devzone...
Hello，
I am using ncs1.7.1, qspi + mx25r64 external flash ota it works well, but I don't know how to change qspi to spi.
I need your help thanks
I change the parament...
Hi Nordic,
I am working on a raspberry pi based gateway which has Thread Border Router and edge node functionality. I have setup the OTBR on the gateway and I have manage...
Hi,
how can I change the standard LED_0 output from P0.17 to P0.03? I am using SES, toolchain 1.8.0 and the nRF52DK board and I would like to flash the sample code to a...
