Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Could someone explain how to power the nRF52840 via USB?
Looking at the schematics, and also reading the "objective" spec, I can see that VBUS is connected to the USB input...
Hello,
Since yesterday's update of the nRF connect extension the device name of the target in the "connected" devices screen is updated from nrf9160_xxAA to nrf9160_xxAA_REV2...
Hi Everyone,
I tried to build lpUart example from samples available. I was trying to debug then I got the breakpoint on
"__ASSERT (lpuart, "Failed to get the device...
i was working on nRF52840 and nRF9160 with NCS v1.8.0.
i'd like to find an API to reboot system. so i tried to call NVIC_SystemReset(). it works in my nRF9160 project. ...
I am currently designing a PCB which incorporates the nRF9160, and I would like to know the devices behaviour in between 2.0 V and 3.0 V, as this is below the minimum VDD...
Dear,
We are working on our custom boards to develop a watch product which need external flash memory connected by QSPI interface. In this product, the UI images and font...
As I learnt, nRF5232 defaut with LDO mode, DC/DC is diabled, but I can not find any config in nRF5 SDK for nRF52 DK,
someone said to use: sd_power_dcdc_mode_set,other said...
Hi,
I've been reading that the nrf9160 can only receive up to ~2KB of data at a time. It seems that the connection terminates if I send too much to the nrf9160. I tried...
Hi again Nordic, I need some pointers. Håkon, a very patient man here, sent me an example code repo of usage of external flash memory on the nRF9160DK. I've tried the sample...
I am trying to bring in the spi_nor driver into our project and was getting errors reading back the jedec id on initialisation so I tried to run the nrf/samples/nrf9160/http_update...
Hello, I have a problem when I enable Bluetooth on my application. If I enable Bluetooth, I can't control gpio pin on Trace DATA. If I disable Bluetooth, I can. It's a hardware...
Hi,
nRFConnect SDK Sample not working (periodic_adv _sync)
I have two nRF52840 DK with nRFConnect SDK 1.7.1
Compiled and run on nRF52840 boards:
\ncs1.7.1 \zephyr...
Hi There
Is it possible to connect to nRF Cloud using a normal 4G/LTE Sim? I see the specs of the NRF9160 show that it supports full LTE and all the Bx bands.
If the answer...
