Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
When I use this example:ble_central\ble_app_uart_c (SDK_17.0.2 S132 nrf52832)
It disconnects every few seconds and reason 0x8.
LOG :
<info> app: conn_Param Update...
Hello! I'm reading the functions that exist in SPU HAL.
The function nrf_spu_flashnsc_set is used to configuring non-secure callable flash region. Which is great to use...
Hi,
I am using the nRF52833DK with NCS v1.6.1 in SES for a multiperipheral application. The application has the LIS2DH accelerometer which is communicating with nRF52833...
I'm using nrf_sniffer_for_bluetooth_le_4.0.0 on Ubuntu 20.04.3 and running `./nrf_sniffer_ble.py --extcap-interfaces` fails on my system. Which also means the nRF52840 dongle...
Hello,
I would like to implement an I²C communication between a nrf52840 and a MCP3221 (which is an ADC).
The first 7-bit of the MCP3121 are 0b1001101. I guess the slave...
Hi!
I have a custom board based mostly of the nrf9160DK, where I need communication between nrf52849 and nrf9160 processor.
I have used the code from this ticket that...
Hi,
I'm using the PCA10056 dev kit and nRF5_SDK_17.0.2. I am aiming to connect multiple initiators to acceptor using Initiator and Acceptor examples. So far I've been able...
Hi There,
When I am trying to write code, I am not clear about the meaning of the code " bearer_adtype_add( BLE_GAP_AD_TYPE_COMPLETE_LOCAL_NAME ); "
I try to check the...
I'm using the Zephyr provided WS2812 LED driver (SPI). I am noticing some strange behavior when my chain-length property is greater than 10.
I connected a digital logic...
Hi Nordic
We are developing our IOT product and we are starting our development of firmware on nRF9160 DK so that we can port that code to our custom PCB that will contain...
Hello
When I output some data using a 'LOG_xxx' macro, I do get debug information over the RTT console like this:
But as you can see there are some extra bytes in front...
Hello,
I wish to send SPI message by 2 Bytes per once, total 102 bytes.
Basically SPI works fine.
I wonder if there is way to reduce inter SPI time. It measured 18u...
Hi,
We are looking at porting the Tuya BLE SDK to the Nordic platform and on reviewing the documentation we have identified that the SDK uses two 16bit service UUIDs:
...
Most of the examples and posts are about the libuarte async driver, but I am using the basic libuarte_drv (not async) and running into difficulty. Without any concrete example...
