I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi everyone, I'm an intermediate level nRF Connect SDK IDE programmer, and I describe my issue below:
1.- In the link below I found an example of code for the analog port...
The SDK version is using version 17 and I am using NRF52832.
I checked the following scope waveform for the next SPI communication.
Question
I want to remove the...
nRF5_SDK_17.0.2_d674dde\examples\dfu\secure_bootloader\pca10056_ble\arm5_no_packs
Why the compiled hex file is different from before, and the code is not modified
I like to use nRF toolbox to monitor my glucose meter. To my understanding, after the glucose device connected with nRF toolbox, they will be exchanging data. So my question...
Hi,
When attaching external GPS Antenna to Nordic Thingy91, I realize that the power consumption increases by about 5mV. Are there any ways that I can config to unuse this...
I just solved this bug, so I'll share my solution.
Bug description: cannot run application after upload via nRF Connect v3.6.1 - Programmer using MCUboot. Upload is successful...
Hello,
I am ble to connect with nRF 52840 using pygatt bluetooth command.
sudo gatttool -b E5:3B:A6:E1:58:86 -I.
[LE]:connect
[LE]:Connection Successful.
Even...
Hi,
I'm using nRF5_SDK_17.0.2_d674dde\examples\peripheral\twi_master_with_twis_slave\pca10040\blank\ses to check I2C as per infocenter TWI testing document.
I have done...
Hello,
I've been using https://github.com/NordicSemiconductor/pc-nrfutil for few years now as a library of my own application to do DFU of a device. Everything worked and...
I am using an nRF52 DK and running a modified version of the heart rate collector example from the pc-ble-driver-py repository.
My modified program scans for connectable...
If you can expect the data to be sent or received at random times over UART, does it make sense to suspend the UART in the driver? Is it fine to leave both TX and RX enabled...
We are building a device where nRF9160 acts as a master that runs Zephyr OS (using NRF Connect SDK). Our device has a 2nd communication interface beside the nRF9160 modem...
Good afternoon.
We are engaged on a project that entails the simultaneous, independent development of two separate modules capable of interacting with the BLE stack. ...
Hello,
Im trying to debug my fw using Keil, its running in debug mode and I have RTT printouts, but once softreset occurs debugger doesnt halt it. Device reboots and starts...
fdsa
1.) From the nRF5 SDK I am using the example project for the Adafruit NFC Tag Reader.
2.) Using the project "as-is" I am able to get some basic information about...
