Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi,
I am trying to convert a number from little endian to big endian. There is a built in function "NTON" that I can use instead of writing my own code, but I can not find...
I'm using two nRF52805 to get sensor values and send 2 sensor real-time values to my phone via BLE. Each nRF52805 BLE works well (Individually tested by nRF Connect App. It...
The encoders I am using generating about 500 pulses per second, and I need to read 3 of them at the same time. I assume a good approach for that is to use the hardware timer...
Hi, working with NCS v1.4.2, I see building products for an <app> landing into subfolder <app>/build/, in several flavours
app_moved_test_update.hex app_signed.hex app_test_update...
Hello,
I'm trying to flash an example code from the SDK onto the Arduino Nano 33 BLE board.
I tried to use the external debugging on an arduino nano 33 ble card but the...
Hi,
I'm using NRF52840 and having a lot of issues with hard fault.
From time to time, I get an application crash with the following log:
HARD FAULT at 0x00000000 R0...
This question may be better suited for the Zephyr forum, but I figured I would ask it here as well in case somebody can easily see what I may be missing.
I am trying to...
I am attempting to use the UART peripheral with a UART device which communicates via 1 start, 7 data, 1 even parity and 1 stop bits.
Is there any? way to configure or fake...
According to this post it seems clear that a peripheral device cannot set the connection event length in a given connection (and only has mild influence on the connection...
Hello,
it's been a couple of days that i have a problem with NRF9160DK.
The problem is related to function getaddrinfo() that is now permanently returning -11, whatever...
Hello,
I wanted to interface LCD with nrf52840, for that we have selected few of them from different vendors. I was looking for display drivers for LCD, but couldn't find...
When building the zigbee network_coordinator example for the nrf52840 dongle the merge.hex is linked to start at 0x0 in flash so the nrf connect programmer won't flash it...
Hi everyone：
New to the DevZone, nice to meet you guys.
I have an problem to the GPIOTE.
I'm now using an AFE4404 to calculate the heart rate and heart rate variability...
Hello, teams!
I'm sorry to bother you.
Now I'm testing mesh function.
I have two questions.
1) Is there good way to show the performance of relay operation?
...
