Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I verify the TLS connection without a certificate in the matt_samples routine. I found that the connection to the server is very slow, it takes more than 20 seconds, how can...
Dear Team,
i have connected a sensor to nRF52810. The sensor power suppply (VDD) is connected to one of the GPIO. My system will switch between systemON and systemOFF most...
Hello
We are just now looking at the implementation of a Bluetooth module for our product and we have previously looked at your module called nRF 52.
I would need some...
Hello Nordic Team I want to use the ble_app_eddystone example found in SDK 15.3 on NRF52832 to advertise in connectable mode from the beginning. I tried to add nrf_ble_es_on_start_connectable_advertising...
Good day!
We have six of the nRF52840-DKs and would like to try coded PHY mesh communication. Is there a link for the SDK which features coded PHY (long-range) mesh? Apologies...
nodic example in \connect SDK\v1.5.0\nrf\samples\bluetooth\peripheral_lbs , ,i can not find the software interface place in peripheral_lbs example code from where to send
Hi.
I'm trying to make the i2cDevlib work on an nRF52 DK board.
There are several ports of the same to nRF51, and one to nRF25 but on the old SDK11.
I'm using SDK15...
Hello,
The Zephyr OS provides a function to reboot the module, sys_reboot(type) where type is either a cold or a warm reboot.
However I cannot find anywhere the difference...
Hello,
We opened from a clean download the example " ble_app_uart " in this folder:
\nRF5_SDK_17.0.2_d674dde\examples\ble_peripheral\ble_app_uart\pca10040\s132\arm5_no_packs...
Hi, Community!
My development environment is the following:
SDK52,
nRF52840,
s140 17.2.0
nRF Sniffer
My problem is that I can not seem to be able to send more...
Hello,
We are working with the nRF52840 and the OTA works when I set 0x10001304 to a value from 0-3. When I set 0x10001304 to a value of 4 or 5, the OTA fails.
Hi there,
I'm developing with the nRF52840 right now.
I'm trying to read some sensordata with TWI. The sensors are BMM150, BMI270 and BMP388.
Unfortunately, I already...
Hi everybody,
I received a nRF52833 DK (PCA10100) and I was capable to install heart rate example dropping prebuilt hex into the mass storage driver. Later I flashed a led...
Hi
I have seen some queries for support asking if app_timer can be used for real time clock and calendar functionality,
i am using the nRF52810 but the answers were either...
