Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
Using 'nrf5_SDK_for_Mesh_v5.0.0_src' exampe project 'light_switch' developed for nrf52 Development Kit(pca10040). How to make the same project working on Thingy52(pca20020...
I am working on a project based on the ble_app_hrs_rscs_relay example project which I have largely extended with many additional services.
For example I am offering an additional...
Hi
I am working on nRF52832 , I want to store the data in NVMC . so I am trying to write the data blockwise , I saw the layout each page consists of Block 0-7 .To each block...
Hi everyone,
Is it possible to implement a USB device belonging to the Personal Healthcare class with the nordic nrf52840 DK?
NRF supports Personal Healthcare USB class...
Hi, I have written these 3 functions to erase/read and write. When I write any value from address 1 it gives following wrong output(0 1 2 3). But When I start address from...
Hi nordic team，
I use the nrf52832 EVK ,I want to connect MIC and speaker to the EVK.
I read the nRF52832_PS_v1.4.pdf, and i guess following interfaces can be used.I don...
Hello
I am using Linux PC
nrf52832
chmod 777 to the nordic serial port
using the bt_nus_shell script :
sudo python bt_nus_shell.py --name BT_NUS_shell --com...
I want to use nrf5340 on DTM mode (installed through nrf connect) to test Carrier frequency offset for CTE packets using CMW500. However, CMW uses power trigger to find the...
I have developed a custom PCB based on nRF 9160. I have followed the connections as per the attached image
Can I use Segger Embeded Studio to program the custom PCBs. If...
Hi there!
How i can put nrf52840 NCP module into low power mode or turn it off? By SPINEL_PROP_MCU_POWER_STATE property of Spinel protocol getting error - "Prop_not_found...
Is it possible to implement a wakeup/power-on-long-push?
Working with the pwr_mgmt example from SDK 17, I see how bsp_wakeup_btn_config works to enable a BUTTON_ACTIVE_STATE...
Hi, I have a project in which I need to connect to an infusion pump via BLE.
I need your urgent help :)
The pump is advertising every 15 minutes for 10 seconds.
how...
hi,
Using nrf52840
setting new mac address results Error 12802:
using mac : 7F:37:DA:47:22:B1
gap_addr.addr_type = BLE_GAP_ADDR_TYPE_RANDOM_STATIC; gap_addr.addr_id_peer...
