hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
Hi there!
We faced the problem of not being able to perform Legacy DFU with Android 10 and newer iOS devices and have since applied the fix. However, since doing so we observed...
Hello,
in our design we use a RF switch behind the ANT LTE antenna I/O of the nRF9160. Many RF switches need DC blocking capacitors in series with the RF signal due to their...
Hi everyone,
When we want to enable a module we usually enable it from the sdk_config.h by setting the desired module to 1 (for example #define NRFX_SAADC_ENABLED 1). I...
Hello, I am using nrf52810 and S112 Softdevice.
After initializing uart, use uart close for uart sleep.
Then the uart close will be checked.
I want to make an uart init...
I have an nrf52832 based device and a mobile app that I'm working on. I'd like to be able to turn the device on via the app, so wake on BLE seems the way to go.
I'm a neophyte...
Hi,
I am working nRF52832 and sdk 16 version. I want to get the RSSI value of my peripheral device nRF52832 and send it to central (phone) over ble ? how to do that ?
...
Hello.
When scanning with the iOS app nRFconnect, the device name is displayed, but when scanning the same device with the Android app nRFconnect, the device name is "N...
I'm trying to test polling on the Thingy91 using the Asset Tracker firmware. However Ion function sensor_sample_fetch_chan(..) I get returning error: -134. I can't find any...
Hi
I created my own application and want to enable CONFIG_DFU_TARGET_MCUBOOT.
But like the picture shows, this marco is still grey in the dfu_target_img_type() function...
Hello, We are looking to send around 1000 Bytes on characteristic. On android app we used Nordic apis to send long write for sending 1000 byes but I am receiving only 509...
Hi team,
My customer is working on design with nRF52832, and they want to know how to defer the low drive mode and high drive mode as below?
Also, shall that be configured...
Hi ,Support Team
My customer is using our nrf5340PDK, their wrong operation caused the DK board become unrecognizable. I use the newest nRF-Command-Line-Tools_10_11_1 to...
Hello,
i am trying to activate eDRX with the unmodified at_host sample on a nRF9160DK. After connecting i get empty strings for <NW-Provided_eDRX_value> and <Paging_time_window...
