I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
hi all ,
how to enable GPIOTE PORT and IN[n] event simultaneously ?(not same pin)
i enable the GPIOTE to trigger interrupt event.
one for the keyboard which need multiple...
Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Hi,
Someone has been working with Alarm Cluster. I tried to implement it on multiprotocol dorr lock example but it was impossible. I have been reading ZCL library revision...
Hello,
I am trying to PCA10040 example project program to NRF52810 BLE module.
I just know that the 52810 has different(small) memory with respect to the 52832.
So,...
I have compiled ble_app_blinky sample code from nRF5_SDK_17.0.2_d674dde SDK and loaded it with s132_nrf52_7.2.0_softdevice.hex in my nrf52382 board. I can discover this device...
Hello,
I want to use a Li-Po battery with my nRF52833 development kit and I can't find the specific name of the J6 connector in the DK documentation. Does anyone know...
Hello ! I am working on the asset tracker project on NCS 1.4.0. Since I switched to this NCS, I have an error that comes up very often (once in two or once in three): get...
Online rajAsthana a few seconds ago in reply to Einar Thorsrud
Hi Einar,
Now I am able to put my board(nrf52840) in DFU mode with buttonless code using Esp32 as...
Hi,
I using nrf52832 evk board and sdk17(S132). I want to add the internal temperature sensor reading to the ble_app_buttonless_dfu_pca100400_s132 code present in the examples...
Hi,
1st time using nRF52840 - EV-BT840 on Keil V5.25.20
I use SDK 1702, reference to example examples\dfu\secure_bootloader\pca10056_s140_ble
My question is what softdevice...
Hey,
I have isnstalled ncs v1.3.1 and the toolchain specified in the instructions ofr 1.3.1.
I am trying to utlise the date-time library in the https_client example. ...
Hi Great Nordic Support Team:
Our clients are developing products with 『 nrf52840-WLCSP』. And they find out that there are some mis-information on the spec.
It's described...
Hi,
Dear nordic friend,I am trying to download NCS1.31 by using toolchain manager,but it work bad,show in below.
I have use some ways，to make me can visit the web in Europe...
Hi, I'm having difficulties driving SDOUT when it's configured to pin 19 on the NRF52840. I can operate the peripheral and see output data when my WS2812_PIN macro is assigned...
Hi all,
I am interfacing with a CAN Controller (MCP25625) that sets an Interrupt pin when data is ready (active low). That pin is then connected to a GPIO on the nRF9160...
Hello
I'm using a passive buzzer controlled by PWM. When PWM is set and run, the buzzer will continue to output small noises.
This is probably a code problem. Below is...
