I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
1. I tested the following AT instruction on ncs v1.3, returned OK, but did not return the subscription message, need to modify where to return the subscription message did...
We are using I2C bus for communication with a RTC and Accelerometer. But sometimes the I2C get struck in i2c_write. It does not happens always it may happen randomly. We are...
Hi,
I just spent several hours trying to figure out why, using a nRF52 dev kit w/ SDK13 + S132 on both central/client and peripheral/server side, sd_ble_gattc_read() was...
Dear Support,
I have a question about the IPv6 networking with OpenThread. I do have an mesh network with about 50 nodes (PCA10059) and implemented CoAP servers and clients...
I just downloaded SEGGER Embedded Studio (ARM V4.52c) and plugged in my rather old PCA10040. It offered to upgrade the driver, which I accepted. Now, when I click "Connect...
Hi,
Just installed nRF Connect v3.4.1 on a macOS Catalina and get the following error message when starting any of the apps:
I've tried both reinstalling and downgrading...
Hi,
I'm making a peripheral device that needs to minimise battery usage.
My device is essentially a beacon but it allows temporary connections to send a stream of data...
Hello,
I have purchased a new nrf52832 DK board for development. I tried to run some examples like ble_app_blinky which are working properly. But when I tried examples such...
Dear All:
Our team are ready to develop a project with multicentral and multiperipheral
The project topology image lists as follow:
I want to ask how many ram it will...
I know this sounds a crazy question but is it possible to flash a custom nRF52832 board with the same firmware that is shipped with the dev kit and create a mass storage out...
Hello,
I am looking to run the ble_app_uart example from the SDK v17 in nRF only mode on the nRF52840 DK. When running the application as is on nRF only mode, it fails during...
I bought nRF51 dongle from mouser.com. I wanted to put nRF sniffer firmware on it using the guide on the web site. I tried using nRF connect programmer but it can not talk...
Dear all,
I've been struggling with SECUREAPPROTECT register in UICR Flash area on a nRF9160 DK.
I would like to restrict and protect Secure code loaded in Secure mapped...
Hi, we have a custom board using the nrf9160, running modem firmware 1.1, and using the nrf9160_gps driver.
Sometimes we see messages like this:
Tracking: 8 Using: 0...
