I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
Hi,
I see there is a differenece between v1.0.0 and v1.1.0 in the asset tracrker's main loop.
i.e. poll function vs the sleep function.
does this result in a change...
Hi,
I'm working on a custom bootloader which does DFU over I2C. As a fail safe mechanism I want to have a timer running that gets reset between each Image data block, so...
When using SDK v13's I2S driver, the data to send is filled via data_handler callback. How do I fill last block data?
Assume i2s buffer size is 2000, then every 1000 words...
I have been going through the steps in this blog post: https://devzone.nordicsemi.com/nordic/cellular-iot-guides/b/getting-started-cellular/posts/getting-started-with-nrf9160...
Hello everybody,
I'll try to modify the ble uart example. The target is, to get data from two different nus Services (different characterisitv uuids). They are both initilised...
I basically need to use two UART instances with the BLE Buttonless DFU Template App.
I started using the Serial library but apparently it's no longer supported.
The methods...
Hello,
I am working on nRF52832 SDK 15.3.0 in segger studio.
In my project I have 2 ADC input pin.
ADC initialization is as shown below,
And every 0.5 second I read...
I have a custom BLE characteristic that I want to use to allow an app to send commands to my device. I use an on-write() function that is called whenever a BLE_GATTS_EVT_WRITE...
The Device's name UUID for Thingy52 in according to this site https://nordicsemiconductor.github.io/Nordic-Thingy52-FW/documentation/firmware_architecture.html is: EF68xxxx...
Hi I am using nrf52840 on a custom board with segger embedded studio as development IDE. I would like to flash the hex file generated without using segger embedded studio...
do you have a user gide for Serial DFU just like buttonless DFU ,like this link https://devzone.nordicsemi.com/nordic/nordic-blog/b/blog/posts/getting-started-with-nordics...
Hi,
I have flashed lte_ble_gateway on nRf9160 DK (PCA10090) and hci_uart on nRF52840 SoC.
After flashing, I am getting some random RSSI values and MAC Address , instead...
Hello,
I have two micro-controllers communicating over SPI.
The STM32F746 is SPI master. The nRF52840 is SPI slave. I use SDK v15.3.
I am sending two bytes over SPI...
Hi.
I had to unpair from the Android Bluetooth list by doing pm_peers_delete () when bonding. It's ok. I know why it should. But sometimes I can't find my paired device...
