Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
I'm testing a gps sample program below. github.com/.../gps
I have two questions about it.
1. It doesn't acquire NMEA data. it always stops working when it reaches 30 sec...
Hi
I tried to connect my dongle to PC but it is not getting detected , Even the red LED is not blinking., Can someone help me out with this issue
Thanks
Tabassum
I'm using LPCOMP to sense multiple input.
I call the lpcomp_read() function below for each input pin.
If I only call this function for 1 pin only, it worked fine.
For...
Hi,
I'm developing an application requiring multiple connections to several peripherals from a single central. I followed the instructions given here https://devzone.nordicsemi...
Does anybody know a quick and easy way to disable the radio functions in a soft-device application?
I want to measure and optimise the power consumption of all the other...
Hi
Can someone suggest me how can i erase the secure bootloader from nrf52840(Dongle),Because am unable to get "erase all" or "erase and write" option in nrf connect application...
Dear Nordic Team,
I can not flash my nRF52840 USB dongle with the nRF Connect Programmer application.
The window looks like this:
Erase / Read / Write functions...
Hi,
I am wondering how connection and scan interval work together when using multilink central device. I am starting scanning (scan interval and window 0x80) again after...
So, after using my Devkit and everything working OK as far as I can tell, I decided to order up a bare BT832XE module and place it on my PCB.
Flashed it with the same firmware...
Hi,
I recently received a NRF9160 DK from DigiKey in U.S. and having trouble doing anything! I am using iBasis SIM card and a the moment my whole experience is like this...
Hi,
I'm currently trying to implement a switch between slow and fast connection parameters. For a certain amount of time during a connection the link between peripheral...
I'm logging the app_error_fault_handler() and I got a reset (on disconnecting, reconecting BLE) from the SoftDevice (id = 1) at address 0x169A8 (pc=92584, info=0).
How can...
Hello, I studied on example\ble_peripheral\ble_app_ancs_c in SDK15.2.0 with board PCA10040. After paring and bonding sucessfully with my iPhone, I reset PCA10040 with Button...
Hi
I am looking to use a pre-certified modules for meshing.
However BLE Mesh have some rather big limitations for the size of network/bandwidth i have in mind and I have...
Hello,
I am searching the way of decoding the motion raw data from thingy 52.
Especially, for the accelerometer values.
In the app, I get the next value:
FAFF...
