Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hello!
I use Segger Embedded Studio. Ubuntu 18.04 I'm trying to build mqtt_publisher project from zephyr samples. And get error: undefined reference to `sys_rand32_get'...
Greetings,
Here are the details:
IDE = SES v4.12
SDK = v15.2.0 and v15.3.0
Hardware = Nordic nRF52 DK (PCA10040 v1.1.1) * 2 and Rigado BMD-300-EVAL * 2 (vB)
I connected...
Can you explain me what I need to do in order to have the esim ? Do I need a physical component ? I am new to this subject if someone can help me a little bit. Thanks
I am trying to measure and characterize expected battery lifetime of my design. I've noticed that as the effective Connection Interval goes up, so does the Rx current peak...
After init I2C channel
#define TWI_INSTANCE_ID 1 // because SPI0 share same reg add with TWI0 we change and enable TWI1
#define MAX_PENDING_TRANSACTIONS 5
NRF_TWI_MNGR_DEF...
Hello,
I am trying to estimate Battery life. I am using CR2032 with 230 mAH capacity. I am confused with the calculations.
As per excels sheet in below link, for 500...
Hi, I have strange problem using pc-ble-driver on nrf52 with heart_rate_monitor example. When I set advertisement data to be 16 bytes long, two of our testing phones cannont...
Hi,
I am using nRF52832 and I need to create a timer interrupt handler, which can trigger at 417us (microsecond). I am using Segger Embedded studio. Please, can anyone help...
I have a project which recently started logging the following error on boot.
nrf_sdh_ble: sd_ble_enable() returned NRF_ERROR_NO_MEM.
This is the only log message....
Hello
I have a simple Thread network with 3 nodes and I would like to send a provisioning request from one to the 2 others in order to get their IP.
I modified the Thread...
I will like to know if the nRF52832 is capable of working properly when placed in series with a 30 Ohms Resistor ( which is the battery resistance for our application) at...
Hello,
As nordic has implemented sdk for mesh and i have been using mesh sdk v3.0.0 LIGHT_SWITCH_EXAMPLE but i am facing some problem regarding pa_lna. Actually wt i have...
Hi,
I want to use I2S to drive the speaker,just like playing the prestored samples from sounds.h in thingy:52.
However,i can't drive the DAC by I2S.Is there anyone have...
I just got my nRF9160 DK. Unfortunately the out of the box demo didn't work:
LTE LC config ... [00:00:01.029,876] [1;31m<err> net_if.net_if_init: There is no network interface...
Imagine following use case:
Alice has a peripheral bonded with Alice's phone (central)
On the peripheral, Alice switches to a "guest mode" which disconnects from Alice...
