Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hi. I have built an ble application which runs on the nrf52832 with softdevice S132 V 6.0.0. In addition to the application and the softdevice I program a bootloader on the...
Hello,
I am learning bluetooth mesh with Light switch demo example. I have downloaded the folder "nRF5-SDK-for-Mesh-master" from the link "https://github.com/NordicSemiconductor...
Hello all!
We have custom HID with multitouch BLE device. We took HID descriptor from USB where this works pretty good, ported it to BLE and it seems not working as expected...
I just upgraded to nRF Sniffer V2.0
The Time column of Wireshark shows wrong values for short delta times. Is is set to "seconds to previous packet"
My advertiser runs...
Dears,
I have a problem with the ble_ant_app_hrm in the examples (multiprotocol). I am using a pca10040 demo board with sdk 14.2 with IDE SES on a MacOS
I have flash...
Hi, I'm using nRF52832 with SDK 15.2 and 3.0 (Mesh). when I try to provision 2 or 3 client/servers the nRF Mesh application behaving properly which means provisioning is happening...
Hello,
I would like to use an usb dongle with nRF52840 above and
- on bluetooth side give an spp or vsp profile
- on usb side be an usb cdc device
the reason is: I...
Hi,
We are currently implementing a mesh application that is expected to have a large number of mesh devices. We have already tested DFU on a smaller mesh and it is working...
trying to bring up the new nRF91 dk with default firmware.
Registered the eSIM. switch sequnce activated with LED 3 and 4 starts blinking. After that LED4 starts blinking...
Hi,
During provisioning of a device the Device Name is changed to the default "nRF5x" after completion of the PB-GATT connection. The name is later on changed back when...
Hi,
I am trying to use latest pc-ble-driver. The code is based on pc-ble-driver-js. When I call sd_ble_gap_scan_start(), I get only one "device discovered" event. This happens...
Hi, I need to use nrf52832 as HID keyboard and send function keys F1-F9 to computer. I have tired to run HID keyboard example in nrf5 SDK. How do I send function keys instead...
Hi,
I tried to build the Connect SDK documentation according to the guide: https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/doc_build.html
I did this on...
APP_TIMER_CONFIG_USE_SCHEDULER affects how are handled. One example is the timer call back is actually called at interrupt level if APP_TIMER_CONFIG_USE_SCHEDULER is zero...
