I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
I can get certain MCUboot features working for the Lesson 8 test program. However, these features don't work when I try to port them over to a fully fledged project. I think...
Hi
This is my first project to make my custom PCB.
I have a question about how can I uploaded my code with segger embedded studio by using nrf52840 dk?
For the hardware...
Hi,
I've create an v2.4.0 SLM application in VS Code by copy from sample, and I am trying to enable trace function for cellular monitor tool app, in order to LOG the packets...
During our evaluation of MQTT, we observed that if we send data every five minutes, the server stops receiving it. We currently believe this is related to CG-NAT, which drops...
Hi I am getting fatal errors when building most of the exercises in the Wifi Fundamental course. I have attached terminal output from building the wififund_less4_exer1_solution...
I have code developed for the nRF52832 based on the Zephyr RTOS. If I switch to the nRF5340 with Zephyr RTOS, would it be possible to develop by simply uploading the additional...
Dear all:
I have built a project(ex: matter bulb) in Nordic SDK, the generated load is zephyr.hex which size is about 2345kb ;
Then I open nRF Connect Programmer, and...
I'm attempting to get our wearable remote to interact with a GoPro using their API and am getting the error in the subject line when attempting to start scanning. I've checked...
I am working on scanning and connecting to an iPhone device in NRF52840dk, but I am not able to receive my iPhone while scanning. If there are any different ways, please let...
Hello!
Looking for some guidance on how I should start debugging an issue I'm experiencing trying to get the Zephyr fdc2x1x sample code running on a custom PCB that uses...
Hi everyone,
I am working with the nRF SDK v2.0.4 for VsCode and with the nRF52840 DK.
I want to develop an application that transfer in real time the data collected...
I'm essentially building a BLE to UART gateway to allow our microcontroller device to talk to our apps. The BLE section is the nRF52840 and I'm trying to simply use it to...
I am trying to install the nrf connect SDK on my Macbook M3 Pro. But i am unable to do so. Neither VSCode extension nor the Toolchain manager works for me.
Clicking install...
I'm currently troubleshooting potential timing-related collisions associated with the NRF radio. I use a custom protocol on a single specified channel (no frequency hopping...
Hi, I have a custom board built around a nRF9161. When I test with the at_client only AT+CGSN=1, AT+CGMI, AT+CGMM and AT+CGMR return with the expected string. All other commands...
