Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hello,
In our project we are using FLASH 2GBIT SPI/QUAD W25N02KVZEIR external flash together with nrf5340. I have made the flash definitions on v2.6.0\zephyr\boards\arm...
Hello,
I am trying to bring up a MBN52832 Bluetooth Low Energy Module supplied by Murata that uses the nRF52832 chip. The BT module is connected to the MCU(STM32F427) via...
Hi,
We are working on nrf5340 board with NS and TF-M setup and we have SDK v2.7.0
We need to have a flash partition to store the some secure data may be a size of 4KB...
The sidebar does not load, this is version v2024.7.13.
I uninstalled it and installed it again as an admin, but it still did not load.
Sometimes it loads for a split second...
I am using a custom board with a nRF52832 (inside a BMD-300 from ublox) that I can't seem to get to a lower power state. The lowest I've been able to get is 2.2mA even using...
Hi,
I'm developing an application on the nRF9160DK with custom firmware for both the nRF52840 as well as the nRF9160 on the board, using VSCode with the nRF Connect extension...
Hi,
I am working on an application with ncs 2.5.0 that is based on a combination of the central_uart example and the hci_lpuart as I'm trying to pass data around between...
Hello,
My goal is to read out UICR address 0x10001080UL from command line / MCUMGR.
How to acheive that?
I have tried and successfully compiled ran these mcumgr handler...
I am useing NCS v2.6.0. Setting "CONFIG_LOG_MODE_OVERFLOW=y", will always print "1 messages droppend" after a period of RTT printing. CONFIG_LOG_MODE_OVERFLOW =n will no longer...
nrf Toolchain: 2.7.0 nrf Connect SDK : 2.7.0 Gateway: nrF5340 Audio DK Headset: E arbud 'MOMENTUM TW 4' (Sennheiser) I try to run and test this following application " Broadcast...
Hello,
I am encountering the following multi registration error when migrating from 2.5.0 to 2.7.0. I don't really have any good way to debug this as the application was...
Hi, could you please point me towards how to solve the following:
CMake Warning at C:/ncs/v2.6.2/zephyr/CMakeLists.txt:862 (message): No SOURCES given to Zephyr library...
