I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
Hi,
I installed nRF Connect SDK (1.9.1) using Toolchain Manager v0.10.3, and nRF Connect for Desktop v3.11.0. Before that I also installed NRF command line tools 10.15.4...
hi,
I want to build and flash only mcumgr bootloader code to my controller , from the example which i observed i am getting that mcumgr is always with some other example...
I use an InsightSIP ISP1907-HT module, I have a 4 layer board to minimise cost. Signals on top and bottom with GND on inside.
I'm concerned that my design could fail emmissions...
Can using whitelist on Central and Peripheral reduce the connection time? In my example I want to advertise every 3secs and want to make sure that the central connects to...
I am completely new to this toolchain and how it works.
I was trying to add a UART sensor to the matter sample project on the nrf52840dk. Is there anyone who can help me...
Hi,
What's the maximum throughput for nRF52832 as peripheral?
S132 7.1 SDS demonstrates configuration for 192kbps. But I noticed that DLE is not yet enabled. So can...
I want to use the timer to measure the interval between two signals, which requires an accuracy of 1us. But in Timer mode, I don't find a register that can read the current...
Hello Nordic semi team,
I am running into an issue with sd_ble_gattc_read
I have set the MTU size to 70 and I do this:
// Configure the gatt MTU size . memset(&ble_cfg...
Hi,
I'm currently development firmware for a application using a Nordic chip. This application will use some drivers allowing the communication with sensors and for the...
Hi,
I have known a case to raise CRC error in secure bootloader with using \nRF5_SDK_17.0.0_9d13099\examples\dfu\secure_bootloader\pca10100_s140_ble
I enabled a nrf_log...
I am writing my own DFU app for the nRF52832. I am using C# and .NET with Visual Studio.
For reasons I don't want to get into I can't use the Nordic SDK library with this...
Hi,
I want to use the app_error_save_and_stop in app_error_weak.c of SDK16
However, the call to the app_error_fault_handler stops to NRF_BREAKPOINT_COND and never reaches...
For clarification I use the nrf5_SDK_for_Mesh_v2.1.1. and the nrf52832.
For a product of ours we use multiple NRF52 as nodes in a mesh that sends data to an application...
Hi fellas,
First of all sorry for the long post but I'm stuck for quite some time now and I need your help. I guess better provide more info than less.
I am working with...
Hello All
during developmenmt we meet some strange phenomen.
the device send to PC 135 bytes on responce command READ.
During transmitrion 135 bytes the softdevice generate...
