Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
I am running the throughput sample project on sdk 1.9.0 using two nRF5340 dev kits and am getting a throughput of 197 kbps using 2M PHY, Data Length 251 and Interval of 7...
Since upgrading to SDK 17.1.0 i get the following warnings of a redundant redeclaration for SystemCoreClock, SystemInit() and SystemCoreClockUpdate() for nrf52810 and nrf52840...
How to upgrade the nRF52832 tag in OpenWRT+nRF52832 gateway
gateway(openwrt+nrf52832) |_____ nrf52832 tag1 |_____ nrf52832 tag2 |_____ nrf52832 tag3 |_____ nrf52832 tag4...
Hi,
I try to install nrfconnectsetup330ia32.exe on my Windows-10 x64 bit computer. The setup program hangs when the progress bar is at about 33%. It just sits there without...
I am currently working on Nrf52840DK board trying to run ble_uart_app. Designed my board and I used BT840 instead of Nrf52840DK . After, code in NRF52840DK is working but...
Using a Thingy!91 (v1.0.0 and v1.4.0, firmware 1.2.3, 1.2.7) I get sometimes (every couple of days) a ENETDOWN when sending data out. Before that ENETDOWN, the device was...
Hello,
I've been working with NRF52840 for a while now. Recently I decided to add extra options to your code so I went to the development kit for a quick test and debugging...
I cannot get the esb ptx sample to compile on NRF52833 device when using VS Code v1.64.2 running windows 10 64bit .
I've installed everything according to videos, and when...
I am developing a nRF52832 based project where I want to position people indoor using an smartband (where the nRF52832 is placed). I was planning to use beacons so I can change...
Hello,
I have a ported a project from Keil (uVision) to Segger Embedded Studio. Everything is compiling, but unfortunately I have a problem with the linker I cannot solve...
Hello,
I am looking for some advices for a personnal project.
I would like to be able to receive all BLE packets ( so all protocols (GATT, SM, LL) and not only GATT) that...
Hi Nordic team,
I have used the nRF5340 BLE Online Power Profiler extensively in the past for things like estimated event energy and estimated battery life. Do you have...
Hello,
I use the nRF52840DK with direct programmed registers for NRF_RADIO peripheral to send and receive 802.15.4 frames. I have also a separate laptop with nRF52840 USB...
