hello,
are there any completed sample code of using pwm0, 1?
just 2 or 3 word can working like following? or need other config?
pwmcon=xx;
pwmdc0=xx;
pwmdc1=xx;
also...
I am planning to migrate to SD 7.0 and SDK 6.0 in order to use the static pass key capabilities. When using the static pass key how should security params be initialized ...
Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I have following the getting started tutorial and install everything mentioned in the documentation.
But the button "Flash" or "Erase and Flash" in VS Code are not working...
The NRF documentation for nrf_pwm_sequence_t says:
When the sequence is set (by a call to nrf_pwm_sequence_set), the provided duty cycle values are not copied. The values...
Hi,
We have implemented FOTA on an nRF52dk (nRF52832) using nRF Connect SDK v1.8.0. That works fine. Now we have encountered a problem that we believe is due to a limitation...
I need to create an IoT QR code reader.
I decide to use the NRF9160 board because it integrates a lot of components that I need to use (LTE, GPS, Bluetooth) so the only...
Hi,
i use event_manager with few modules.
One module use Sensor LIS2DH driver that read data via i2c data when triggered and send it to other module as event.
Second...
Hi,
I'm using nRF52805.
The main power is 3.3V LDO output.
When main power is out, the battery(3V, Coin battery) should be a power source of nRF52805.
But, when battery...
Hi,
I've just returned to working on an nRF52811-based project after a year so I'm a little rusty, and I'm wondering if it is necessary to explicitly call SystemInit() ...
Hello,
I'm experimenting with nRF Connect SDK 1.9.1 and I want to use SAADC, however I'm running into the following error message.
Please note that the code compiles....
I planned to use THE UARTE of nRF52840, but I encountered some problems when I added it to the project from the routine of SDK17.0.2. I compared the UARTE and sdk_config.h...
Hi,
I would like to help/influence the course of our on-going project with nRF52832 such that the recommended/default Toolchains are used. In this regard I have the following...
HI All
Im having endless trouble with nRf Connect and Vs code. @Ovind was kind enough to assist from the first time I failed to get this working, but it was short lived...
Hi,
I've been building nRF52840 applications from the command line using the zephyr RTOS for a while, but having taken delivery of the Thingy:91, am unable to get the hello_world...
Hello,
I am unable to build basic blinky project outside the NRF Connect sdk.
Board - Thingy 91 - nRF9160
SDK version - 1.7.0
builiding through command line tools...
I'm using NCS 1.8.0 and nRF9160 DK, and I need to convert unix_time from int64_t to string, my problem is exactly what is reported in these cases:
devzone.nordicsemi.com...
