I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Hello,
we are currently developing a new prototype board with the nRF52840-chip.
In order to figure out the best performance for our bt-antenna we decided to plan our...
i want to use orientation interrupt of bmi160. but i don't know how to read interrupt data. I wrote it after looking at the data sheet, but I want you to let me know if there...
I'm trying to get Thread working on the nRF52820. It seems that neither the "nRF5 SDK for Thread and Zigbee" nor the "nRF Connect SDK" support it (yet?), but instead require...
Hi,
I understand that when a peripheral is advertising it is also waiting for connection/scan requests.
Does those requests and responses sent via the same advertising...
Hello!
I'm trying to send a mcumgr packet over uart between the nrf9160dk_nrf9160 and the nrf9160dk_nrf5284.
To do this I have a SMP srv and a shell on both MCUs.
...
How do I get following combination to work:
Nrf connect 3.6.1 power profiler with PCA10040 v1.2.1 + PCA63511 v1.1.0 with external power supply and external DUT
The same...
My error messages in Segger studio are messed up (shown below). Everything else is fine. Can I change the font or something?
[m[K'[01m[Kdev[m[K' undeclared (first use in...
Hello, I have a 52832 using SDK16.0.0, that acts as an advertising peripheral (anyone can connect to it), and as a central, connected with 1-1 bond to a peripheral (a 52811...
Hi, using the Nordic power profiler 2 (PP2) kit to measure the current draw of my nRF52833 DK. I have followed the instructions to setup/prepare/wire the PP2 to my DK and...
In the task, when I do a TWI read via nrf_drv_twi_rx(), in the second iteration of the thread, the driver function returns NRF_ERROR_BUSY.
Is it that the driver takes longer...
I've built a custom board using nRF52832 which uses SDK 16.0.0 and softdevice version s113. A part of application is audio streaming/ decibel calculation and transmission...
Hall Mr. Nordic,
I'm sending a 16bit payload with 51822.
The receiver 24L01 is receiving all perfectly. The receiver 52840 is loosing the first two bytes ...
nRF51822...
Hi,
I'm using nRF52840 as my server and the android mobile is my client. At the client end, I'm using the nRF Connect app. It seems like the 50 bytes of data is taking around...
Hello,
I have an nRF9160 DK board (I believe the version is PCA10090 1.0.0) and would like to use the external flash that comes with this board.
Upon inspection, this...
