Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
I use a app_timer_create() function to create a task(200ms once)
when in the task_timeout_handle() ,
I do something more than 200ms,
what will this timer going ?
Hi!
I use nrf51-pwm-library ( github.com/.../) to control brightness of LED RGB light source and it works ok till I don't want to adjust brightness slowly (dimming function...
Hello,
We have been using FDS in our nrf52832 based product. Recently we had a need to port application to nrf52810. It required some flash memory optimization. Fortunate...
Documentation states “When a connection is created it will inherit the transmit power from the initiator or advertiser leading to the connection.” In my BLE event handler...
Hi,
SDK16
I'm using ble_cus.c to define custom BLE service.
In the ble_cus.h file the definition of the UUID is
#define CUSTOM_SERVICE_UUID_BASE {0xBC, 0x8A, 0xBF...
Using just the nRF Connect SDK, I cannot get a push button to interrupt the NET CPU on the nRF5340DK.
I have the following code on the APP CPU:
nrf_gpio_pin_mcu_select...
L2CAP connection oriented channels can be used to transfer frames of up to 65533 bytes. L2CAP is a record oriented protocol. When receiving L2CAP data, using the softdevice...
I have purchased eval kit and entered bootloader mode by pressing BOOT/RESET button while powering up the device but haven't put any file but now when i power up the device...
Hi,
We are in a stage where we want to perform certification of a product and are now looking into an application that can be used to this end. The board is using SDK 15...
Hi,
I've bought a nRF52840-DK kit to evaluate a Nordic BLE SOC (we are interested in using the nRF52811). I've installed SEGGER Embedded Studio 4.52, and obtained a Nordic...
Hello, I am I'm a Beginner at developing NRF 51822. My Development Environment sdk : 12.3 IDE: KEIL v5 SoftDevices : s130
I am developing using the example of 'ble_app_uart...
Hi everyone,
I am trying to understand the Memory layout of nRF52840 SOC in order to apply RAM retention into specific section. Looking the memory layout at pg 21 of the...
Hello Nordic community,
I have a nrf52-DK with SDK15.2.0 and I'm trying to communicate with ST HTS221 sensor. I have the original STEVAL-MKI141V2 evaluation board.
I...
Hello,
I was wondering what examples we have in nRF Connect SDK (NCS) for firmware updates over BLE and serial (receiving an image from another device over UART). Specifically...
Hi
I have bought NRF5340-PDK board to study BLE-MESH. I found that there is 2 development tool in Nordic website
1. nRF connect SDK
2. nRF connect for Desktop
...
Hi,
I have a custom PCB that uses the nRF9160 and an RGB LED. I want to drive this LED with PWM but it uses an active LOW style of GPIO drive. I have been able to use normal...
