Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I tested the nrf beacon application, it allows only the beacons with company identifier 0x0059 (nordic's id). But i need to modify it to support all the device, how...
Hello,
I am trying to understand how to use an external button. In the first stage I am trying to replace the functionality of button0 on the DK with a GPIO.
I took the...
Hey guys,
I'm working with a Laird BL652-DVK (nrF 52832 - chip), Nordic SDK v.14.2.0 and SES (Segger Embedded Studio v.4.30). I'm working with the ble_peripheral example...
Hi, We are using the nRF52840 in a 3V battery powered product. We have an on board 1.8V LDO regulator that supplies Vdd and Vdd_IO. We have a problem with the NFC antenna...
Dear all
I currently have a single nRF52832 SoC (custom PCB) transferring data to a single nRF51 dongle via BLE, which in turn passes the data to my PC via UART. I have...
Hi everybody,
I'm having a problem with the advertising function of the SoftDevice.
When the application starts advertising the function "sd_ble_gap_adv_start()" returns...
Hello,
We are currently looking for a way to test nRF52804 on our board with CMW500. From R&W video clip, they tested Nordic eval. board with USB connection. How do I make...
I’m interesting particularly nRF52832 and nRF52840 (with and without bootloader)
So looking at flash layout with bootloader :
is the section ‘Application data’ available...
i want to send string over eddystone tlm...and wish to use temperature part for this...so how can i display character string instead of temperature in eddystone TLM..please...
Hi, I am trying to use the iOS nRFMeshProvision SDK to create a iOS mobile application. I am trying to get the composition data but access layer always times out and gives...
Hi, I am new to Dev Zone. I am writing debounce logic and I am wondering if a button can have an interrupt set when the GPIOTE sense a HITOLO transition to fire the first...
Hello, I'm currently developing BLE_SCANNER(GATEWAY) for asset tracking or management.
My scan environment is,
[Our device -- same UUID]
The number of our beacons...
Hello. I have the same problem with https://devzone.nordicsemi.com/f/nordic-q-a/54373/uart-logging-backend-hangs-in-nrf_bootloader_app_start/220132
But this thread was stuck...
I'm trying to register a handler to determine when a system event occurs?
Previously on older design kits, I used softdevice_sys_evt_handler_set(......) to register the...
Hi,
I've managed to code an app for nRF52382 (S132, SDK14) which works properly. Also, I've taken "bootloader_secure_serial" and removed a lot of stuff to code a simple...
