Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
Hi,
I have been using nRF51822 with my Android app using Android's Bluetooth Low-Energy APIs.
In order to get more details, I am currently working on integrating the Android...
I'm looking at interfacing a typical Wheatstone bridge sensor to the nRF51822 ADC. This particular sensor only requires a mA or two for excitation and the output fits within...
When use the "nRFBeacons" app to update the info on my beacon the following happens:
Go to update tab.
Select "Connect"
Press "SW2" on beacon and see the LED begin flashing...
I am using s110 and nrf51822. I've set up up a long characteristic of 154 bytes.
Sending between 1 and 154 bytes works as expected.
Sending 155 - 160 bytes gets rejected...
Hi,
I am currently trying to set up the HTTP Application Update Sample and unfortunately it keeps stopping at the "downloading" state. Code is exactly the same from the...
Hi,
I´m using nrf52840 with softdevice S132 and set ble_gattc_conn_cfg_t::write_cmd_tx_queue_size to larger than 1. I´m count number of queued writes by increasing a counter...
I am currently developing with nrf52832 sdk14.2. I found in the test that after opening the hid service, the connection parameters will become the following parameters after...
I encountered a scenario where I call sd_ble_gap_connect() and get an event BLE_GAP_EVT_TIMEOUT with source BLE_GAP_TIMEOUT_SRC_CONN . This is followed immediately by an event...
Hi, i have written code in android, where i am using threads to connect to 832 ble over insecure RFComm socket..
Am not pairing with 832 in my app and am directly trying...
Hi I am implementing a buttonless_DFU function right now. I decided to do Buttonless on my project's PCB Board because it is no longer an environment where I can add switches...
My setup is as follows:
nRF5 SDK 13.1 with s132 5.1.0
nRF52832_AA
Keil 5.25pre
I use RTC1 counter for timestamping along with app_timer timers. My get_timestamp() function...
I am trying to send lots of data through radio (basing on old micro esb project from github, but heavily modified).
I need to keep radio IDLE (not DISABLED) when not transmitting...
Hi,
I am developing smartphone controlled BLE door lock based on nRF52840.
The door lock is a peripheral (also GATT server) and the smartphone is central (GATT client...
Using the nRF52840 with SDK15.3.0 and S140, I am seeing strange interactions between PWM and BLE.
The PWM is configured to create a continuous 175kHz output just under...
I am currently developing with nrf52832 sdk14.2. When nrf52832 is bound to a different iphone connection, if the stored binding record of nrf52832 is already full, will the...
Hello,
We require a bluetooth low energy IC with MCU. Right now we are testing with nrf51422 development board. Could you please suggest any updated ICs with (BLE+MCU) ...
Hi
Below picture and attached file is my 52810 hardware.
All the component are accord with the 52810 data sheet.
But, when I download the BLE blinky project from the...
Hi I am currently testing Buttonless DFU using SDK 12.3, nRF52832 DK. Example test was conducted first using the DK board, but as you can see in the picture, it will fail...
Hi,
I have a MQTT-sample based application running and everything works fine. If I supply the DK through a USB cable connected with my computer, LED 5 blinks high frequently...
