Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi All
I am a newbie with the nRF52 series SoC's and my end goal is to make a solar powered weather station.
I have a very crude nRF52832 dev board that I program with...
Hi, team.
There is a connection nfr52840 and esp32 (115200, 8, no parity, flow disable).
I'm using UARTE in interrupt mode (to send AT command and receive responses)....
Hi there, I am using the MDBT50Q-1MV2 Raytac module, with the nRF52840, and i have noticed that I have a very noisy VDD supply pin. Which definitely a problem because measures...
The qspi driver seems to make a number of assumptions about the protocol that don't fit the Winbond W25M02GW (and certain other) SPI flash chips.
Two major issues I've run...
I'm developing on an nRF52832 that has a serial connection with an iMX6 that is running a Python script with pySerial. For a while I had flow control disabled and would get...
hi i want to build a system with 500 device they send some data to controller wireless how can i do it with blu mesh ?
which chip should i select ? i prefer nrf52832
and...
nRF5_SDK_for_Thread_and_Zigbee_v3.1.0_c7c4730
nRF52840 Prewiew develpoment kit
I try to merge thread dfu client with simple coap server. there is error which i cant...
Hi! So I'm trying to use the throughput example with the nRF51422 board. infocenter.nordicsemi.com says that the SDK 12.3.0 throughput example will work with S130, which will...
Hi,
I want to interface sensor which has minimum requirement of UART supporting baudrate 921600 or SPI guaranteed maximum communication speed : 20 MHZ(Measured at 5cm...
Zigbee OTA upgrade example uses the Zigbee OTA cluster recommendations concerning the firmware file name (that is used for the version control and prevention of the downgrade...
Hi all,
We have custom board which has On Board Jlink support with nRF52832 using STM32 chip(STM32F072CBT6).
We are able to flash and debug using the On Board Jlink. ...
Hi there,
I was hoping someone could help me out. I recently got a hold of the nRF5 SDK for Mesh v2.0.1, and had a play around with the light switch example. I modified...
Hi,
I am trying to program my custom PCB using nRF 52 DK (I am using PCA10040 , nrf52382) as I have done countless times before. But suddenly embedded studio is giving me...
