When I initialize the SoftDevice with SOFTDEVICE_HANDLER_INIT(NRF_CLOCK_LFCLKSRC_XTAL_20_PPM, false); // Sets up Crystal Source to 20ppm 32.7628kHz
The project I based...
I am trying to make a product with NRF8002B. I finally have the product prototyped. The user will connect to the device, beep, light up, and track. It will always stay on...
Please,
It seems that "Flow Control" signal is not available on nRF24AP2-USB.
EVENT_TRANSFER_TX_START event message appears only one time after the first data packets...
I am looking for cheapest (up to few hundred USD) and simplest Arduino basic solution to track real-time RFID tags distance (also direction if possible) without additional...
Hi all,
I am new to Nordic semiconductor but I could be interessed by nRF9E5. To check if it could fit my requierement, I would like to know if it possible to configure...
Hi,
I am using ADC without external reference and no analog input in order to measure the battery level with a timer (code at the end).
I am also reading several ports...
Hi,
I'm programming the nRF51822 and save some user data into the FLASH by using pstorage_update . It works fine if I set system off mode, and wake it up. I can read back...
I have noticed that when I run in release mode, turn WDT on, write bonding info, clear bonding info, and reset, my application suddenly uses 2mA more and takes 5 minutes ...
Hi all:
My iOS app use iOSDFULibrary to update my ble.But when the device enter into DFU mode ,it disconnected for a while.
This is my log:
2018-11-27 21:00:11.122263...
Hi Nordic.
Now I am working on a BLE smart card and am adding an external power amplifier. For low power consumption, i decided to give power only when I want PCB doesn...
Hi,
I tried to use nRF52 evaluation kit to program my custom board for that I have used Debug port P19 in evaluation kit. It was working in the beginning but after sometime...
Hello,
I tried to follow the instructions in this tutorial: github.com/.../nRF52832-buttonless-dfu-development-tutorial
1) I flashed this file via nrfjprog: examples\dfu...
The power estimation tool on https://devzone.nordicsemi.com/power/ maxes out at a minimum interval of 7.5ms and a maximum payload of 27 bytes, with 824mA average current....
Hi,
We need to develop an android app that can only scan a nordic ble and send out advertisment packet in our own customised UI and format. Getting the NRF_connect android...
Hi . .
I want to read the data and sent over ble UART app (via ble )
For that I am using Twi sensor ,in order to send the data what are the changes I need to do in twi...
Purchased nrf52840-DK boards for evaluation. Tested ESB protocol example successfully using Segger environment.
1. I could not find any prints on my host screen after i...
hi.......
how to choose the slave address for peripheral device ?
i am using nrf52382 and segger version 15.2
because i want to pass the address in twi sensor
guide...
Hello, Professional，I meet a strange phenomenon,now I use the nrf52832 IC, when I use the ble_app_hrs_freertos in SDK 11, the Power consumption is nomal, The Average current...
Hi,
I am using nRF24L01P and facing issue of RF Performance varies with batch to batch of nRF24L01P with built-in Antenna. To evaluate the performance of the IC and Antenna...
I am trying to run the blinky example together with freertos (nRF52840 pDK, pca10056, segger studio), so I took the hrs_freertos example and added ble_lbs service from blinky...
Hello, I bought part number NRF52832-QFAA-R7 (E0). I dont know (E0) mean. I can't find any information about it in datahseet. Is NRF52832-QFAA-R7 (E0) similar with NRF52832...
