Hi Hakon.... when i compile my project i get some linker errors,
._build\gzll_host_ack_payload.axf: Error: L6218E: Undefined symbol __main (referred from arm_startup_nrf51...
I'm trying to perform communication between my device and iOS and I ran into some problems. For tests I'm using iPod touch 5 with nRF Toolbox and LightBlue apps and nRF51822...
I've been using Master Emulator API 2.1.3 in Visual Studio 2010 Express, and have spotted a fix I may need in 2.1.5 so I've switched to using the 2.1.7 API. However, I've...
Hello,In normal condition, I use UART,pwm,spi an so on.Now I want to clear the configuration, and enter System ON mode.But I don't want to system reset.
How should I do...
Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi,
We are currently planning to start a project using the nRF52832 as our controller, SEGGER Embedded Studio version 5.42a as the IDE, and nRF5 SDK version 17.0.2 as our...
The scan window does not alternate properly with the BT_LE_SCAN_OPT_CODED option in the scan parameters. Specifically, the scan window does not toggle on and off every 30...
Hi. I want to report 2 observed bugs about board creator wizard of NCS 2.8.0.
1. When you click on "Create a new board", the first thing that you must enter is human-readable...
I'm trying to activate low power mode without success. I found samples but it appears not to work with the last NCS version. I want to get basic GPIO INPUT values at 32khz...
Hi,
1. I am testing nRF54L15 PDK PCA10156 0.8.1 Example is: ncs\v2.8.0\nrf\samples\bluetooth\direct_test_mode 2. Which pins can be used as UART TX and which pins can be...
Hi,
We are currently planning to start a project using the nRF52832 as our controller, SEGGER Embedded Studio version 5.42a as the IDE, and nRF5 SDK version 17.0.2 as our...
Trying to set up UART/UART0 for async. I cannot get the uart interrupt config to shut off.
CONFIG_UART_INTERRUPT_DRIVEN =n is set in the prj.conf
In config output...
Maybe the title doesn't make that clear.
First of all, I have customed my own nrf54l15 board, and I successfully built and run some ncs demos.
Now, I want to do something...
Hello Nordic team,
just received my first hardware and try to port my code which I developed by using the 54L15PDK board with SDK 2.7.0. At the PDK everything did run fine...
Hello,
What is the max data size for NUS?
According to BLE data throughput in the S140 document, it looks like 247 but the data was sent successfully with NRF_SDH_BLE_GATT_MAX_MTU_SIZE...
Hello, I want to configure the radio between two nRF52810 devices. I have an external 32.768 kHz clock and the NN02-101 antenna. My question is: how can I configure the radio...
Hi all,
Ive been able to develop for a few weeks with our nrf52840 device and were able to run our code and do some basic Bluetooth stuff. Suddenly I can no longer flash...
Hi，
How to resolve the following burning errors: PDK:PCA10156 0.8.1
SDK ncs v0.8.0
example :peripheral_uart
Thank you for all your assistance. Kind regards, Peter...
Dear devzone, I used two nRF52840-DKs to download v2.8.0\nrf\samples\bluetooth\mesh\dfu\distributor and v2.8.0\nrf\samples\bluetooth\mesh\dfu\target programs, and configured...
I have gone through the training on debugging because I am getting a stack overflow error, however the debugging screen does not have RAM on it, like it shows in the Dev Academy...
