Hi, everyone~
My goal is to collect data from 4 sensors simultaneously using iPhone.
Now, my testing code for sensor nodes is working fine. It was built based on the...
I am an android developer and I am using your nRF Master Control Panel (BLE) product as published on Google play. Below is the link to the app:
play.google.com/.../details...
I want to build a USB dongle, so I purchased the nrf24lu1+ development kit. However, in order to program the target board, it would seem that I need the nrfgo. Is this correct...
Hi Nordic,
I would like to re/program my device using a OTA BLE Bootloader but i don't want others to copy my firmware or at least make it very hard. As far as i know there...
After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
Hi
I have an external NOR flash chip which is powered off on startup. The idea is to power up the flash when needed to reserve power. On startup, I get the error message...
I haven't found much documentation yet regarding multiple threads in the secure partition, so I wanted to ask if this would be possible. Was planning to also test it out myself...
Hi,
We have a requirement to not exceed 63 mW of WiFi Tx power at any time for any band (2.4 or 5 GHz) . There is a statement about changing Tx power is not supported. Can...
Hi, We are currently migrating our project, originally developed with NCS version 1.8.0, to the latest NCS 2.7.0, while incorporating MCUboot for both of them. During this...
Hello,
I am encountering an issue with the nrfutil settings generate command. Each time the command is executed with the exact same parameters, the resulting settings.hex...
SoC: nrf52840
SDK: OpenConnect 2.4.4
I have been developing an ambient noise system using I2C microphone, nrf52840 and Zigbee networks for some time. The firmare reads...
Hi,
Is nRF52811 / S140 capable of simultaneously being in peripheral (connected slave) and central (connected master) mode like described in this blog post https://jimmywongiot...
I’m working with the nRF5340 and nNF Connect SDK 2.6.1. I’m encountering an issue where, after a central device (e.g. an Android phone) forgets a bonded peripheral device...
There was a previous discussion about the option to disable/enable slave latency a few years ago:
Did this ever get implemented? Specifically interested in the feature when...
SDK: 2.6.1
I needed to add a single wire support to our device recently and I did that by using two pins TX/RX shorted and UART. It works, but current consumption sky rockets...
Hi all
How would I be able to generate and view the calculated hash that i get while using the dfu library? Is there an easy way. I'm hoping to generate one single hash...
I am looking for the code example of how to setup A-GPS/A-GNSS on a nrf9160 dk, but I am not able to find one. I am only able to find these links:
https://developer.nordicsemi...
Hi everyone, I'm encountering an issue with MCUboot on NCS 2.7.0 and my custom board based on the nRF52840. The bootloader was functioning correctly with NCS 2.4.0, but now...
Hello,
I'm using nor flash with qspi as an external storage.
I'm facing problem where i can have different NOR Flash chips (with different jedec-id). Is there a way to...
I am testing ble_app_hid_keybpard of SDK17.1.0 using nRF52-DK board. After running, if BLE connection is not made, it enters Sleep_Mode after slow advertise. At this time...
