After modifying the ancs example to remove the data and control points, the event_connect() subfunction in ble_ancs_c.c gets called immediatly upon a connection to a master...
Using nRF51822, I define keys and pins as follows:
Keyboard key
Mouse left/right key
Mouse move (up/down/left/right)
Media play/pause key
Pin 0 Mouse...
The bluetooth device keeps getting disconnected from the app, even when its not 'idle'.
I am using the android app mentioned here .
I need help getting started to solve...
Moving from SDK version 5.1 to 6.0, the buttons on my PCA20006 beacons no longer works as expected. When I press a button, it seems to register the release of a button incorrectly...
I posted another question along these lines, about using the Timeslot API to get observer behaviour with the S110 v7.0 SD, but I am having trouble getting it to work.
Are...
I'm interested in creating a time of flight algorithm and am trying to calculate what to expect for accuracy.
Is it possible to get an IRQ from when the sync arrives at...
Hi,
using nrf connect SDK v3.1.1
using nrf54L15 development board.
I have been trying to return set uart in low power mode and resume uart low power from a button press...
Hi, I interfaced the Quectel EC200U GSM module with the nrf5340dk. Now I want to do the FOTA with the help of GSM . Is there any example documents or any experince. And also...
I am trying to make the nrf9161 go to very low power mode for 10 seconds and then come back online.
Actually I would not mind if it were to start all over again when coming...
Hello,
I am using the example on the Nordic DK to get UDP messages from the Hologram API to the Nordic Modem. AT#XUDPSVR=1,6002 #XUDPSVR: 3,"started" OK
I very inconsistently...
Hello,
I am working with the nRF9151 board and trying to read SIM/eSIM information.
Steps I followed:
Used nRF Programmer → Erase all.
Opened Board Configuration ...
Dear Nordic
We are evaluating a wearable device and plan to use nRF54H20 be our MCU,
Since our device will be a small form factor and Nordic not released datasheet yet...
Hi, I'm working on nRF9151 on custom board, NCS 3.1.0 and I'm building application with TF-M enabled. I've encountered quite a strange problem. If I remove all UART instances...
Hi,
using nrf sdk connect 3.1.1
using nRF54L15-PDK evaluation board.
Steps to reproduce issue:
1. Setup my board into low power. my branch mark is ~2.9uA.
2. Perform...
I use BLE for one-to-many connections. Usually, the peripheral device should first broadcast, then establish the connection for communication, and finally disconnect. However...
Hi there! I am trying to set up external flash (w25q64) with my NRF52840 project over SPI. I have adapted the spi_flash sample in an attempt to set up this device, but I am...
Hello,
We are developing a product based on the nRF54L15, using BT Mesh. We also use the FLPR. For communication between the cores, we use ICMSG.
Separately, ICMSG and...
Hello!
I am completely new to embedded development and i am becoming quite desperate.
I have ordered a custom board which has an nrf52840 chip on it and a vl53l1cxvofy1...
I am using the nPM1300 MIKROE Click board with an ESP32 over TWI (I2C) . I am facing an issue when VDDIO is sourced from VOUT2 using the onboard VDDIO_SEL jumper .
Although...
I have an odd issue with an older nRF52840-DK, I can flash and read memory from the device just fine but no matter what version of NCS I use, it will not execute whatever...
