Hi All,
I am using nRF51422 with softdevice s310. And implementing Cycle speed and cadence receiver. most of the data processing is fine but i am facing one problem.
...
Hello Nordic Team,
I have a problem with programming the nRF24LE1 chip.
I am developing a small system, which consists of a uC STM32F4xx and a nRF24LE1 Radio Module. The...
Hi,
I'd like to learn about the app compatibility for the new OTA DFU that ships with the new SDK 6.0.0 and S110 7.0.0. I am using a nRF51822 board and I've observed that...
I'm curious to know if there is a tool that allows easy design of a GATT server DB that is portable across dev platforms (the nrf518 EK, my Android/iOS dev environment etc...
Iam trying to display the uart data as a scanned response.nRF51822 receives the data from PIC and it is displayed as scanned response during advertising.the problem is nrf51822...
Hi,
This is a bit more of a typo report.
In the Debug Logger doc page , app_trace_init() is supposed to return an int but in its function declaration it's said to return...
Hello All,
I'm trying to build a receiving unit using the nRF24L01+ and PIC16F628A. Im using an nRF24L01+ and RaspberryPi as my TX unit which i managed to get working ...
hi
I send message from nrf52840_A to nrf52840_B
log shows R eceived CoAP message that does not match any request or resource
Is there a sending format for coap? thx
Hi,
Our product is based on nRF5340 and will run DFU over BLE.
Now I am testing the DFU function via the "Firmware Upgrade" in device manager APP.
In the current architecture...
hi, could you tell why I build SDK17.1.0 (nRF5_SDK_17.1.0_ddde560\examples\peripheral\csense_drv\pca10040\blank\arm5_no_packs) demo code, it appears that mistake (.\_build...
I am trying to send data in peripheral but my central connected to other peripheral .
So I decided to add whitelist in central.
In which function to add whitelist
...
Hi!
I would like to add into my Zephyr project a library called Vanetza , which depends on Boost++, Cryptopp and GeographicLib. I am still learning CMake and I don't know...
Hi
sdk : ncs v2.1.0
example : serial_lte_modem
I used the following command to test and found that sending the character "failed, how should I set it so that I can...
Hello,
I'm working on an application that uses the aws_iot_send function ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrf/libraries/networking/aws_iot.html...
How to make nRF Connect SDK submit to other code management servers (such as bitbucket,Not github), And continue to use Git to manage this code?
I will modify the content...
Hi all,
I recently installed the nRF Connect SDK and have had some success. Very snazzy.
I have seen some issues with the JLink on the DK resetting during firmware validation...
I cannot seem to get floating point supoort for printf/scranf
It works for LOG_INF
I have tried the following .conf settings:
CONFIG_NEWLIB_LIBC =y
CONFIG_NEWLIB_LIBC_FLOAT_PRINTF...
Hi All!
I am trying to program the external nrf9160 SOC using nrf9160 DK using the following connections. Before that, I tried the same connections to program the nrf52820...
When I set CONFIG_LOG=y, CONFIG_SERIAL=y in prj.conf, the UART streams out diagnostic message from my application code as expected, but I also get this endless I2C error message...
I am using NRF52832 for my project.
Refer the following Softdevice and SDK versions.
Softdevice: S132_2.0.0-7.alpha
SDK Version: 4.0.0-2.alpha
Question 1:...
I am using nRF Connect SDK 1.9.0 and the NRF52840.
When building samples/keys/hw_unique_key you get this warning:
----------------------------------------------------...
